Ремонт: Ноутбуков, Компьютеров https://vlab.su/ |
|
P7P55, P7H55 ранний POST-код 1D https://vlab.su/viewtopic.php?f=224&t=4267 |
Страница 1 из 1 |
_AVP_ [ 29 сен 2011, 17:00 ] | |
Заголовок сообщения: | P7P55, P7H55 ранний POST-код 1D |
Одна платка после ремонта питателя Vtt, вторая пришла такой. На второй заменен юг- нет эффекта, на первой заменен еще мульт - тоже самое... Что такое 1D для AMI не нашел. |
KVM [ 01 окт 2011, 10:50 ] | |
Заголовок сообщения: | Re: P7P55, P7H55 ранний POST-код 1D |
Если поможет то пост код 1D - Первичная настройка системы Power Management |
_AVP_ [ 02 окт 2011, 00:16 ] | |
Заголовок сообщения: | Re: P7P55, P7H55 ранний POST-код 1D |
KVM писал(а): Если поможет то пост код 1D - Первичная настройка системы Power Management Это для award. В начальном посте я писал, что БИОС AMI |
KVM [ 02 окт 2011, 00:46 ] | |
Заголовок сообщения: | Re: P7P55, P7H55 ранний POST-код 1D |
вот по ами (в этих табличках есть этот код) AMIT BIOS Post Codes (Prior to April 1990): 01 NMI is disabled and the i286 register test is about to start 02 i286 register test has passed 03 ROM BIOS checksum test (32Kb from F8000h) passed OK 04 8259 programmable interrupt controller has initialized OK 05 CMOS interrupt disabled 06 Video system disabled and the system timer checks OK 07 8253/4 programmable-interval timer test OK 08 Delta counter channel 2 OK 09 Delta counter channel 1 OK 0A Delta counter channel 0 OK 0B Parity status cleared 0C The refresh and system timer check OK 0D Refresh check OK 0E Refresh period checks OK 10 Ready to start 64KB base memory test 11 Address line test OK 12 64KB base memory test OK 13 System-interrupt vectors initialized 14 8042 keyboard controller checks OK 15 CMOS read/write test OK 16 CMOS checksum and battery OK 17 Monochrome video mode OK 18 CGA color mode set OK 19 Attempting to pass control to video ROM at C0000h 1A Returned from video ROM 1B Display memory read/write test OK 1C Display memory read/write alternative test OK 1D Video retrace test OK 1E Global equipment byte set for proper video operation 1F Ready to initialize video system 20 Video test OK 21 Video display OK 22 The power-on message is displayed 30 Ready to start the virtual-mode memory test 31 virtual memory mode test started 32 CPU has switched to virtual mode 33 Testing the memory address lines 34 Testing the memory address lines 35 Lower 1MB of RAM found 36 Memory size computation checks OK 37 Memory test in progress 38 Memory below 1MB is initialized 39 Memory above 1MB is initialized 3A Memory size is displayed 3B Ready to test the lower 1MB of RAM 3C Memory test of lower 1MB OK 3D Memory test above 1MB OK 3E Ready to shutdown for real-mode testing 3F Shutdown OK- now in real mode 40 Ready to disable gate A20 41 A20 line disabled successfully 42 Ready to start DMA controller test 4E Address line test OK 4F System still in real mode 50 DMA page register test OK 51 Starting DMA controller 1 register test 52 DMA controller 1 test passed, starting DMA controller 2 register test 53 DMA controller 2 test passed 54 Ready to test latch on DMA controller 1 and 2 55 DMA controller 1 and 2 latch test OK 56 DMA controller 1 and 2 configured OK 57 8259 programmable interrupt controller initialized OK 58 8259 programmable interrupt controller mask register OK 59 Master 8259 programmable interrupt controller mask register OK 5A Ready to check timer interrupts 5B Timer interrupt check OK 5C Ready to test keyboard interrupt 5D Error detected in timer or keyboard interrupt 5E 8259 programmable interrupt controller error 5F 8259 programmable interrupt controller OK 70 Start of keyboard test 71 Keyboard controller Ok 72 Keyboard tested OK 73 Keyboard global initialization OK 74 Floppy setup ready to start 75 Floppy controller setup OK 76 Hard disk setup ready to start 77 Hard disk controller setup OK 79 Ready to initialize timer data 7A Verifying CMOS battery power 7B CMOS battery verified OK 7D Analyzing CMOS RAM size 7E CMOS memory size updated 7F Send control to adapter ROM 80 Enable the setup routine if <Delete> is pressed 82 Printer data initialization is OK 83 RS-232 data initialization is OK 84 80x87 check and test OK 85 Display any soft-error message 86 Give control to ROM E0000h 87 Return from system ROM 00 Call the Int19 boot loader AMI BIOS Post Codes (After April 1990): 01 NMI is disabled and the i286 register test is about to start 02 i286 register test has passed 03 ROM BIOS checksum test (32KB from E8000h) passed OK 04 Passed keyboard controller test with and without mouse 05 Chipset initialized...DMA and interrupt controller disabled 06 Video system disabled and the system timer checks OK 07 8254 programmable interval timer initialized 08 Delta counter channel 2 initialization complete 09 Delta counter channel 1 initialization complete 0A Delta counter channel 0 initialization complete 0B Refresh started 0C System timer started 0D Refresh check OK 10 Ready to start 64KB base memory test 11 Address line test OK 12 64KB base memory test OK 15 ISA BIOS interrupt vectors initialized 17 Monochrome video mode OK 18 CGA color mode set OK 19 Attempting to pass control to video ROM at C0000h 1A Returned from video ROM 1B Shadow RAM enabled 1C Display memory read/write test OK 1D Alternate display memory read/write test OK 1E Global equipment byte set for proper 1F Ready to initialize video system 20 Finished setting video mode 21 ROM type 27256 verified 22 The power-on message is displayed 30 Ready to start the virtual mode memory test 31 Virtual memory mode test started 32 CPU has switched to virtual mode 33 Testing the memory address lines 34 Testing the memory address lines 35 Lower 1MB of RAM found 36 Memory size computation checks OK 37 Memory test in progress 38 Memory below 1MB is initialized 39 Memory above 1MB is initialized 3A Memory size is displayed 3B Ready to test the lower 1MB of RAM 3C Memory test of lower 1MB OK 3D Memory test above 1MB OK 3E Ready to shutdown for real-mode testing 3F Shutdown Ok - now in real mode 40 Cache memory now on...Ready to disable gate A 20 41 A20 line disabled successfully 42 i486 internal cache turned on 43 Ready to start DMA controller test 50 DMA page register test OK 51 Starting DMA controller 1 register test 52 DMA controller 1 test passed, starting DMA controller 2 register test 53 DMA controller 2 test passed 54 Ready to test latch on DMA controller 1 and 2 55 DMA controller 1 and 2 latch test OK 56 DMA controller 1 and 2 configured OK 57 8259 programmable interrupt controller initialized Ok 70 Start of keyboard test 71 Keyboard controller OK 72 Keyboard test OK...Starting mouse interface test 73 Keyboard and mouse global initialization OK 74 Display setup prompt.. Floppy setup ready to start 75 Floppy controller setup OK 76 hard disk setup ready to start 77 Hard disk controller setup OK 79 Ready to initialize timer data 7A Timer data area initialized 7B CMOS battery verified OK 7E CMOS memory size updated 7F Enable setup routine if <Delete> is pressed 80 Send control to adapter ROM at C800h to DE00h 81 Return from adapter ROM 82 Printer data initialization is OK 83 RS-232 data initialization is OK 84 80x87 check and test OK 85 Display any soft error message 86 Give control to ROM at E0000h A0 Program the cache SRAM A1 Check for external cache A2 initialize EISA adapter card slots A3 Test extended NMI in EISA system 00 Call the INT19 boot loader AMI Plus BIOS: 00 Control to Interrupt 19 01 NMI disabled (Bit 7 of I/O port 70h) 02 286 register test over 03 ROM checksum OK 04 8259 PIC initialization disabled 05 CMOS Interrupt disabled 06 System timer (PIT) counting OK 07 Channel 0 of 8259 PIC test OK 08 DMA channel 2 of delta count test OK 09 DMA channel 1 of delta count test OK 0A DMA channel 0 of delta test count OK 0B Parity status cleared (DMA/PIT) 0C Refresh and system time check OK (DMA/PIT) 0D Refresh link toggling OK (DMA/PIT) 0E Refresh period ON/OFF 50% OK 10 About to start 64K memory 11 Address line tested OK 12 64K base memory tested OK 13 Interrupt vectors initialized 14 8042 keyboard controller tested 15 CMOS Read/Write test OK 16 CMOS checksum/battery tested 17 Monochrome mode set OK (6845) 18 Color (CGA) mode set OK (6845) 19 Video ROM search 1A Optional video ROM OK 1B Display memory Read/Write test OK 1C Alternate display memory OK 1D Video retrace check Ok 1E Global byte set for video Ok 1F Mode set for mono/color OK 20 Video test OK 21 Video display OK 22 Power on message display OK 30 Readying virtual mode memory test 31 Virtual mode memory test started 32 Processor in virtual mode 33 Memory address line test 34 Memory address line test 35 Memory below 1MB calculated 36 Memory size computation OK 37 Memory test in progress 38 Memory initialization below 1MB 39 Memory initialization above 1MB 3A Display memory size 3B Ready to start memory below 1MB 3C Memory test below 1MB OK 3D Memory test above 1MB OK 3E Ready to switch to real mode 3F Shutdown successful 40 Ready to disable gate A-20 (8042) 41 Gate A-20 disabled (8042) 42 About to test DMA controller (8237) 4E Address line test OK 4F Processor in real mode 50 DMA page register test OK 51 DMA unit-1 base register OK 52 DMA unit-1 channel register OK 53 DMA channel-2 base register test OK 54 About to test both units OK 55 F/F latch tests both units OK 56 DMA units 1 & 2 programmed OK 57 8259 PIC initialization OK 58 8259 PIC mask register check OK 59 Master 8259 PIC mask register OK 5A Check timer and keyboard Interrupt 5B PIT timer Interrupt OK 5C About to test keyboard Interrupt 5D ERROR! Timer/keyboard Interrupt 5E 8259 PIC Interrupt controller error 5F 8259 PIC Interrupt controller test OK 70 Start of keyboard test 71 Keyboard test OK 72 Keyboard test OK 73 Keyboard global data initialize (8042) 74 Floppy controller setup about to start 75 Floppy controller setup OK 76 Hard disk controller setup about to start 77 Hard disk controller setup OK 79 About to initialize timer data 7A Verify CMOS battery power 7B CMOS battery verification done 7D Analyze test results for memory 7E CMOS memory size update OK 7F Check optional ROM C0000h 80 Keyboard sensed to enable setup 81 Optional ROM control OK 82 Printer global data init OK 83 RS-232 global data init OK 84 80287 check/test OK 85 About to display soft error 86 Give control to system ROM E0000h 87 System ROM E0000h check over 00 Call to Interrupt 19 for boot loader |
_AVP_ [ 02 окт 2011, 09:35 ] | |
Заголовок сообщения: | Re: P7P55, P7H55 ранний POST-код 1D |
тоже не подходит... это от очень старых биосов коды. До инита памяти (до D3) ни о каком видео речи идти не может. Возможно код чисто асусьный, никто не встречался? |
KVM [ 02 окт 2011, 11:57 ] | |
Заголовок сообщения: | Re: P7P55, P7H55 ранний POST-код 1D |
Если логически подумать то всеравно это связка:процесор-север- память,там копать нужно,если питание на памяти в норме(питание памяти и ее терминации) то проверить питание севера и клок если в норме то на процентов 99 что проблемма в севере или отвал сокета процесора,ну и как вариант просто мог биос глюкнуть(можно попробовать перешить его). |
Dem0n [ 02 окт 2011, 12:16 ] | |
Заголовок сообщения: | Re: P7P55, P7H55 ранний POST-код 1D |
На ней случаем не нового образца бивис где даже мыша работает? Если он то 0x1D - 0x2A OEM Pre-memory initialization codes |
_AVP_ [ 02 окт 2011, 16:24 ] | |
Заголовок сообщения: | Re: P7P55, P7H55 ранний POST-код 1D |
KVM писал(а): Если логически подумать то всеравно это связка:процесор-север- память,там копать нужно,если питание на памяти в норме(питание памяти и ее терминации) то проверить питание севера и клок если в норме то на процентов 99 что проблемма в севере или отвал сокета процесора,ну и как вариант просто мог биос глюкнуть(можно попробовать перешить его). Севера здесь просто нет (он в проце). Юг менялся, питания все проверил (и +1.5 на памяти есть, терминирование памяти 0.75 есть). Биос тут еще не EFI (который с мышкой и графический). БИОС шил на обеих. Отвал сокета маловероятен, т.к на одной из них чинил питание еще до этого кода, на деформации не реагирует. Сигнальные линии между памятью и процом прозвонил-ОК. Код похоже какой-то ОЕМ, он появляется еще ДО D3 (чтение EEPROM памяти). |
_AVP_ [ 16 ноя 2011, 00:37 ] | |
Заголовок сообщения: | Re: P7P55, P7H55 ранний POST-код 1D |
Одну мать победил - замена клокера. Вторая так и осталась... |
Avastas [ 16 апр 2017, 18:27 ] | |
Заголовок сообщения: | Re: P7P55, P7H55 ранний POST-код 1D |
На рабочей Asus P7P55 LX пост d1 дохлый проц |
ganibal86 [ 06 авг 2018, 02:31 ] | |
Заголовок сообщения: | Re: P7P55, P7H55 ранний POST-код 1D |
Тоже такая же беда, мульт и клокер менял, ничего не поменялось, есть ли у кого еще какие мысли ? |
Страница 1 из 1 | Часовой пояс: UTC + 4 часа |
Powered by phpBB © 2000, 2002, 2005, 2007 phpBB Group http://www.phpbb.com/ |