Всех приветствую, товарищи!
На ремонте Philips 32PFL4208T, который постоянно перезагружается. Загружается полностью, выходит канал и примерно через 2-3 секунды перезагружается. Материнская плата у него 715G5675-M01-000-005K. Я снял лог - в конце выводит код [AppManager:removeFocusProc]no more proc[ 28.716692] Restarting system. И затем уходит на перезагрузку.
В сети на этод код не смог найти информацию.
Подскажите пожалуйста, ясно ли из кода, из-за чего перезагружается система? Это ошибка в NAND и система не может найти следующую команду для выполнения?
UART_Philips 32PFL4208T
Boot-
DRAM Channel A Calibration.
Byte 0 : Gating(2 ~ 77), Size=76, Mid=41, Set=41.
Byte 1 : Gating(2 ~ 67), Size=66, Mid=36, Set=36.
Byte 2 : Gating(2 ~ 72), Size=71, Mid=39, Set=39.
Byte 3 : Gating(2 ~ 72), Size=71, Mid=39, Set=39.
Byte 0 : DQS(8 ~ 43), Size 36, Set 24.
Byte 1 : DQS(8 ~ 43), Size 36, Set 23.
Byte 2 : DQS(6 ~ 44), Size 39, Set 23.
Byte 3 : DQS(12 ~ 41), Size 30, Set 22.
DRAM A Size = 1024 Mbytes.
Boot
Start Pmain
0x0000a000
Nand boot
NID=0x1590dc98
LZHS addr:0x00100040
LZHS size:0x001f9470
LZHS checksum:0x00000038
Boot
Start Lmain
MT5880 Boot Loader v1.11
SIF_Master0: new design
Boot reason: A/C power on!!
[PDWNC] PDWNC_PHILIPS_ReadWakeupReason: 6 (status 0x0)
-------------use external edid, disable internal edid------------------
IR DATA register : 0x 0
T8032 init A/C on case loader stage...
Load T8032 FW (addr: 0x d454f8, size: 24286)success!!
T8032 FW version: 20
T8032 change to loader stage...
LDR_FlashCopy 0xf010 0x73800 0x80
Detect NAND flash ID: 0x1590DC98
Detect TC58NVG2S3ETA00/I0 NAND flash(SLC): 512MB
NAND_BDM_Mount: Partid=0, offset=0x0, size=0x200000
NAND_BDM_Mount: Partid: 0, Total Block Count: 16, Bad Block Count: 0
1st MAC in EEP is valid (1c:5a:6b:40:bd:b7)
1st : (1c:5a:6b:40:bd:b7)
2nd : (1c:5a:6b:40:bd:b7)
[PDWNC] Current state : 0x1
[PDWNC]PDWNC_PHILIPS_DetermineNextState : u4Event = 0x6
PDWNC_PHILIPS_DetermineNextState : u4Current = 1
PDWNC_PHILIPS_DetermineNextState : system booting
PDWNC_PHILIPS_DetermineNextState : event = PDWNC_WAKE_UP_REASON_AC_POWER
Read EEPROM OK at PDWNC_PHILIPS_GetLoungeMode
PDWNC_PHILIPS_DetermineNextState : Lounge mode = 0
Current = 0x1, Event = 0x6, Next = 0x1
[PDWNC] PDWNC_PHILIPS_EnterNextState : u4Next = 0x1
[PDWNC]PDWNC_ReadWakeupReason = 0x6
[PDWNC]Enter normal mode, LED changes to normal
PDWNC_Init
USB0: Set GPIO63 = 1.
USB1: Set GPIO64 = 1.
Display 0x00efea60 background:0x00000000
Find panel index 184 from EEPROM
OSD_SetPlaneSwitchOrder[0,1,2],Switch[1,2,3]
---------- [SA7] vErrorHandleInit ----------
[SA7] Error handling init
[SA7] PANEL_GetPanelWidth=0x556, PANEL_GetPanelHeight=0x300 , wDrvGetOutputHTotal=0x898 , wDrvGetOutputVTotal=0x465
[SA7] PANEL_GetHTotalMax=0x794, PANEL_GetHTotalMin=0x604, PANEL_GetVTotalMax=0x3cc, PANEL_GetVTotalMin=0x30a
[SA7] PANEL_GetPixelClkMax=85000000, PANEL_GetPixelClkMin=72000000
[SA7] PANEL_GetPixelClk60Hz = 0x4e27603
---------- [SA7] vErrorHandleSetByTiming ----------
[SA7] u2HSyncWidth=260, u2HSyncStart=1930, u2VSyncWidth=26, u2VSyncStart=1094
---------- [SA7] vErrorHandleSetByTiming end----------
---------- [SA7] vErrorHandleSetByPanel end----------
[SA7] vDDDSInit
---------- [SA7] vErrorHandleSetByTiming ----------
[SA7] u2HSyncWidth=30, u2HSyncStart=1382, u2VSyncWidth=3, u2VSyncStart=800
---------- [SA7] vErrorHandleSetByTiming end----------
vDrvSetOCLKClockSchemaInit.
[SA7] _fgVopllUseDDDS = True
[LVDS] VOPLL Initialize successful !
LDR_OsdDisplay(14, 0x00d66060, 1280, 291)
Color:14 BmpAddr:0x00d66060 Width:1280 Height:291
Panel 1366 x 768
*************u4BmpPitch=5120******************
Do USB upgrade
USB: Vbus turn up time = 1643 ms, Max =0 ms.
USB-0: insert.
USB-1: insert.
USB-0: ClassCode= 0x9, u4Diff=117 ms.
FIND_CLASS_HUB.
HUB No USB Medium on Hub.
USB upgrade stop
Flash load lzhs header from 0x80000 to dram(0x1526270), size=2048
Decompression uboot to 0x00800000...
Flash load image from 0x80000 to dram(0x1526270), size=0x403e6
NAND_BDM_Mount: Partid=5, offset=0x700000, size=0x400000
NAND_BDM_Mount: Partid: 5, Total Block Count: 32, Bad Block Count: 0
Flash load tz from 0x21ab97(kernel) to dram(0x3f200000), size=0x2b599
secure boot ok
secure boot ok
Starting image...
▒
U-Boot 2011.12.12 (Aug 11 2014 - 10:51:37)
DRAM: 725.3 MiB
WARNING: Caches not enabled
NAND: Detect NAND flash ID: 0x1590DC98
Detect TC58NVG2S3ETA00/I0 NAND flash: 512MB
512 MiB
0.0.0.0
In: serial
Out: serial
Err: serial
Boot from kernelB and rootfsB(partition 7)
error, env space is not enough
Net: Net Initialization Skipped
No ethernet found.
Hit any key to stop autoboot: 0
Partition rootfsA defined at mtdparts:
ID:6, Offset:0x00000000, Size:0x00b00000
Loader succeeded in signature verification
## Booting kernel from Legacy Image at 00007fc0 ...
XIP Kernel Image ... OK
OK
Starting kernel ...
TZ Heap: start=0x3FA5CC80, end=0x40000000
TZ dram: start=0x3F000000, end=0x40000000
[ 0.000000] timekeeping_init done
INIT: version 2.86 booting
Loading /etc/profile...
Start readahead /etc/readahead_early
Running rc.local...
net.ipv4.tcp_window_scaling = 6
INIT: Entering runlevel: 3
**********DirectFBInit()
commandline read: app_man
~~~~~~~~~~~~~~~~~~~~~~~~~~| DirectFB 1.4.0 |~~~~~~~~~~~~~~
(c) 2001-2009 The world wide DirectFB Open Source Community
(c) 2000-2004 Convergence (integrated media) GmbH
----------------------------------------------------------------
======DFB 3DMM u4VirtAddr : 0x3a6c5000, and DFB 3DMM u4Size : 0x1f80000======
[input_add_device][1629]
[LinuxInput_Initialize][2172]
[input_add_device][1629]
[LinuxInput_Initialize][2172]
[input_add_device][1629]
[LinuxInput_Initialize][2172]
[input_add_device][1629]
[LinuxInput_Initialize][2172]
[input_add_device][1629]
[LinuxInput_Initialize][2172]
[input_add_device][1629]
[LinuxInput_Initialize][2172]
[input_add_device][1629]
[LinuxInput_Initialize][2172]
[input_add_device][1629]
[LinuxInput_Initialize][2172]
[input_add_device][1629]
[LinuxInput_Initialize][2172]
[input_add_device][1629]
[LinuxInput_Initialize][2172]
[input_add_device][1629]
[LinuxInput_Initialize][2172]
[input_add_device][1629]
[LinuxInput_Initialize][2172]
[input_add_device][1629]
[LinuxInput_Initialize][2172]
[input_add_device][1629]
[LinuxInput_Initialize][2172]
[input_add_device][1629]
[LinuxInput_Initialize][2172]
[input_add_device][1629]
input thread's parent pid is 517 tid is 517
[LinuxInput_Initialize][2172]
[input_add_device][1629]
[DirectFB]: Wait to Init IR...!
[input_add_device][1629]
dfb_set_cursor_border [0,0,1280,0]
[dtv_app_mtk]>InitDRM
[dtv_app_mtk]>drv_init as 0x39 model
[dtv_app_mtk]>drv_init as EU model
[dtv_app_mtk]>HDMI fast booting init...
[ 9.163571] NAND_SDM_Mount: Partid=15, offset=0x1d680000, size=0x2980000
input thread pid is 517 tid is 538
original scheduler policy 0
scheduler nice 0
original child scheduler policy 0 prio 0
new child scheduler policy 2 prio 99
Start to wait IR event...
[dtv_app_mtk]>
[dtv_app_mtk]>TVD MsgCtrl: NRL:60/40, PER:100/90
[dtv_app_mtk]>x_drv_init end!!
[dtv_app_mtk]>[ FakeDM ] Init...
[FakeDM] Init FM...
/dev is created./mnt is already existed. That is OK.
/mnt/usb is created.[FakeDM] FM inited...
[FakeDM] Init SMB...
[FakeDM] SMB inited...
[FakeDM] do coldboot start...
[DM] _dm_open_dev_thread: entered
[DM] _dm_nfy_req_thread enter
[DM] _dm_nfy_req_thread get_nl_sock:25
[DM] _dm_cb_msg_thread enter
[DM] usbfs mounted.
[FakeDM] do coldboot end!!!
Init chip_spec_init!!!!!
EEPROM size is 0x4000.
{CI_glue}:ci_eng_init
{CI_glue}- expect PROD key
{CI_glue}- c[1]
88888888888888 PHYSICAL_Init() entered 888888888888888
88888888888888 ITC_Init() entered 888888888888888
88888888888888 PHYS_DRVOpen() entered 888888888888888
88888888888888 STB_CIOpen() entered 888888888888888
88888888888888 STB_CIOpen() ended 888888888888888
{CI}CI_RegInterrupt_nfy
88888888888888 PHYS_DRVOpen() entered 888888888888888
[ACFG_CUSTOM] acfg_custom_get_svl_tsl_dual_bank ui1_g_svl_tsl_dual_bank == DUAL_BANK_SVL_TSL_INVALID and get form plf is 255
[ACFG_CUSTOM] acfg_custom_get_svl_tsl_dual_bank Line 9751
[ACFG_CUSTOM] acfg_custom_get_svl_tsl_dual_bank: MAIN
{CDB} Loading metadata (version 7)
{CDB} Loading metadata (version 7)
{CDB} Loading metadata (version 7)
{CDB} Loading metadata (version 7)
{CDB} Loading metadata (version 7)
{CDB} Loading metadata (version 7)
{CDB} Loading metadata (version 7)
[dtv_app_mtk]>
[dtv_app_mtk]> ~~~~~~~~~~~~~~~~~~~~~~~~~~| DirectFB 1.4.0 |~~~~~~~~~~~~~~
[dtv_app_mtk]> (c) 2001-2009 The world wide DirectFB Open Source Community
[dtv_app_mtk]> (c) 2000-2004 Convergence (integrated media) GmbH
[dtv_app_mtk]> ----------------------------------------------------------------
[dtv_app_mtk]>
[dtv_app_mtk]>[dfb_input_core_join][974]
[dtv_app_mtk]>dfb_set_cursor_border [0,0,1280,0]
window size: 0
stacking [0x2], layer_id [0]
Init DSMCC[5][3][2]
MHEG5 TPS start to setup
[MHEG5_NVM]rw root path = /3rd_rw
MHEG5 TPS setup failed to create dir(-6)
EEPROM size is 0x70.
[dtv_app_mtk]>
[dtv_app_mtk]>
x_wifi_cli_init~~~
[dtv_app_mtk]>
[dtv_app_mtk]>
Rec_util_thread:buffer addr 0x00003d79b000,size 0x380000
{HBBTV_DSMCC} Init HBBTV DSMCC
{DT} Real Time Clock is available on this system.
EEPROM size is 0x70.
=====================
channel id:(2883713), svl rec id:(11), channel id in rec:(2883713), brdcst type:(2)
=====================
{CI}Is a CI+ CAM = 0, the mode = 0, cur mode = 0
reason: 0x00000006 - 0x00000000
[dtv_app_mtk]><AM> wakeup reason = 6
EEPROM size is 0x35b0.
EEPROM size is 0x4000.
reason: 0x00000006 - 0x00000000
[dtv_app_mtk]>[OT][_acfg_ch_lst_load_p1][723]: e_wakeup_reason = 6.
{CDB} Loading metadata (version 7)
{CDB} Loading metadata (version 7)
{CDB} Loading metadata (version 7)
{CDB} Loading metadata (version 7)
{CDB} Loading metadata (version 7)
{CDB} Loading metadata (version 7)
<PLF_OPT> Align option codes (OPC_USED[NVM] - OPC1 OPC2 OPC3)
16 _app - 16 16 16
224 _app - 224 224 224
48 _app - 48 48 48
0 _app - 0 0 0
38 _app - 38 38 38
128 _app - 128 128 128
192 _app - 192 192 192
15 _app - 15 15 15
159 _app - 159 159 159
255 _app - 255 255 255
127 _app - 127 127 127
61 _app - 61 61 61
235 _app - 235 235 235
4 _app - 4 4 4
0 _app - 0 0 0
0 _app - 0 0 0
TP vision IP SW - Mbdsl1(13.00.00.01)initializaiton-successful
reason: 0x00000006 - 0x00000000
[dtv_app_mtk]>[a_cfg_custom_bds_update_mutirc_state] state = 0
BGM: Power mgmt init
[dtv_app_mtk]>[BGM] [OTG] _bgm_otg_init
[dtv_app_mtk]>BGM: Update scan init
[dtv_app_mtk]><BGM CAM>: cam scan component init
[dtv_app_mtk]>[BGM_OAD_DTC] _oad_detect_init
[dtv_app_mtk]>[BGM_OAD_DLD] _oad_download_init
[dtv_app_mtk]>BGM: Ambilight module init
[dtv_app_mtk]>_stvapi_app_init_fct
ERR: _CHL_RCHL_RealChannelMatchT(1365): Assert(pt_realChannel->e_idType == IDType_DVBT_T)
ERR: _CHL_RCHL_RealChannelMatchT(1365): Assert(pt_realChannel->e_idType == IDType_DVBT_T)
ERR: _CHL_RCHL_RealChannelMatchT(1365): Assert(pt_realChannel->e_idType == IDType_DVBT_T)
ERR: _CHL_RCHL_RealChannelMatchT(1365): Assert(pt_realChannel->e_idType == IDType_DVBT_T)
ERR: _CHL_RCHL_RealChannelMatchT(1365): Assert(pt_realChannel->e_idType == IDType_DVBT_T)
ERR: _CHL_RCHL_RealChannelMatchT(1365): Assert(pt_realChannel->e_idType == IDType_DVBT_T)
ERR: _CHL_RCHL_RealChannelMatchT(1365): Assert(pt_realChannel->e_idType == IDType_DVBT_T)
{svl}x_svl_read_common(0x1016113)=0,size=1536
reason: 0x00000006 - 0x00000000
[dtv_app_mtk]>[NAV_OPTION_LIST_CUSTOM.C] nav_option_list_custom_get_be_netfilx_or_not and bool_is_in_netflix_mode = 0 at line 4770
<ACFG> The min/max/pos of h-pos in driver is wrong.
<ACFG> The min/max/pos of v-pos in driver is wrong.
[NAV]SVL_ID= 1, ui_tuner_type = 0, ui1_svl_lst_idx = 0 @Func = nav_sort_svl_rec
[NAV]SVL_ID= 2, ui_tuner_type = 1, ui1_svl_lst_idx = 0 @Func = nav_sort_svl_rec
Set country code to [RUS] by SB_KEY_TYPE_COUNTRY_CODE
[DRV_INTERFACE] Get Operation Error. (-16)
[D-interface return ERROR] [DRV_CUSTOM_CUST_GET_SPEC_GPIO_ID] i4_ret = -16
[D-interface Warning] [DRV_CUSTOM_CUST_GET_SPEC_GPIO_ID] e_gpio_type=[10], get GPIO_ID = 0
GPIO = 0 Output 2
[dtv_app_mtk]> GPIO pin number invalid.
[dtv_app_mtk]> ****FIX ME****, acfg_custom_post_init:8489
****FIX ME****, acfg_custom_post_init:8489
****FIX ME****, acfg_custom_post_init:8489
[DRV_INTERFACE] Set Operation Error. (-16)
[ ACFG_CUST] c_scc_vid_set_game_mode, OFF
<ACFG> set 3D nav: SEMI_AUTO, ret = 0
_edb_dvb_process_restart_edb_nfy
open root EDB_tuner_ter_dig_0
{EDB} _edb_dvb_load_table Ok!
_edb_dvb_process_restart_edb_nfy
_edb_dvb_process_restart_edb_nfy
_edb_dvb_process_restart_edb_nfy
_edb_dvb_process_restart_edb_nfy
_edb_dvb_process_restart_edb_nfy
{EDB} begin free 1 message
_edb_dvb_process_restart_edb_nfy
_edb_dvb_process_restart_edb_nfy
{EDB} begin free 1 message
{EDB} _edb_dvb_free_table Ok!
{EDB} free root Ok!
open root EDB_tuner_ter_dig_0
{EDB} _edb_dvb_load_table Ok!
[dtv_app_mtk]>
[dtv_app_mtk]>
[dtv_app_mtk]> S/W Version
[dtv_app_mtk]>
[dtv_app_mtk]> TPM1013E_003.011.000.001
[dtv_app_mtk]>
[dtv_app_mtk]> NVM Version
[dtv_app_mtk]>
[dtv_app_mtk]> 2.00
[dtv_app_mtk]>
[dtv_app_mtk]>reason: 0x00000006 - 0x00000000
[dtv_app_mtk]>{EDB} begin free 1 message
_edb_dvb_process_restart_edb_nfy
{CDB} Loading metadata (version 7)
{CDB} Loading metadata (version 7)
{CDB} Loading metadata (version 7)
_edb_dvb_process_restart_edb_nfy
{CDB} Loading metadata (version 7)
{CDB} Loading metadata (version 7)
{CDB} Loading metadata (version 7)
{CDB} Loading metadata (version 7)
{EDB} begin free 2 message
_edb_dvb_process_restart_edb_nfy
{CDB} Loading metadata (version 7)
{CDB} Loading metadata (version 7)
{EDB} begin free 2 message
{CDB} Loading metadata (version 7)
{CDB} Loading metadata (version 7)
{CDB} Loading metadata (version 7)
_edb_dvb_process_restart_edb_nfy
{CDB} Loading metadata (version 7)
{CDB} Loading metadata (version 7)
_edb_dvb_process_restart_edb_nfy
{EDB} begin free 3 message
{CDB} Loading metadata (version 7)
{CDB} Loading metadata (version 7)
_edb_dvb_process_restart_edb_nfy
{CDB} Loading metadata (version 7)
{CDB} Loading metadata (version 7)
[INET] 11.465, x_net_ip_v6_auto.4720 >>> (eth0->eth0, b_restart_if = 0
[INET] 11.466, x_net_network_reg_nfy.4297 >>> {EDB} begin free 3 message
0x410a7ff8, 0x00000000
[INET] 11.469, x_net_ni_enable.1455 >>> if enable eth0->eth0
_edb_dvb_process_restart_edb_nfy
{EDB} _edb_dvb_free_table Ok!
{EDB} free root Ok!
open root EDB_tuner_ter_dig_0
{EDB} begin free 3 message
{EDB} _edb_dvb_load_table Ok!
[NAV]SVL_ID= 1, ui_tuner_type = 0, ui1_svl_lst_idx = 0 @Func = nav_get_svl_handle
_edb_dvb_process_restart_edb_nfy
{EDB} begin free 3 message
_edb_dvb_process_restart_edb_nfy
_edb_dvb_process_restart_edb_nfy
{EDB} begin free 3 message
_edb_dvb_process_restart_edb_nfy
{EDB} begin free 4 message
_edb_dvb_process_restart_edb_nfy
{EDB} begin free 4 message
_edb_dvb_process_restart_edb_nfy
_edb_dvb_process_restart_edb_nfy
{EDB} _edb_dvb_free_table Ok!
{EDB} free root Ok!
open root EDB_tuner_ter_dig_0
{EDB} _edb_dvb_load_table Ok!
{EDB} begin free 5 message
_edb_dvb_process_restart_edb_nfy
{EDB} begin free 5 message
[INET] 11.579, x_net_network_reg_nfy.4301 >>> call eth0 enabled
_edb_dvb_process_restart_edb_nfy
_edb_dvb_process_restart_edb_nfy
{EDB} begin free 6 message
_edb_dvb_process_restart_edb_nfy
{EDB} begin free 6 message
_edb_dvb_process_restart_edb_nfy
_edb_dvb_process_restart_edb_nfy
{EDB} begin free 6 message
[NAV_OPTION_LIST_CUSTOM.C] nav_option_list_custom_get_be_netfilx_or_not and bool_is_in_netflix_mode = 0 at line 4770
{EDB} begin free 6 message
{EDB} begin free 5 message
vc_cre initk]>
vc_hiden init>
[GCC_OSRC] osrc create
{EDB} begin free 4 message
<wfd-------->>: _nav_wfd_init is called !!
[WFD MSG]Create msg notify 0x1035731
left 64 top 210.
{EDB} begin free 3 message
{EDB} begin free 2 message
{EDB} begin free 1 message
[dtv_app_mtk]>
left 64 top 253.
[dtv_app_mtk]>
left 64 top 195.
[INET] 11.758, x_net_ni_reg_ev_notify.2015 >>> dev: wifi0->wifi0, event: 1, plugin
[INET] 11.759, x_net_ni_reg_ev_notify.2015 >>> dev: wifi0->wifi0, event: 2, unplug
lru_list_create.
lru_list_create.
[INET] 11.772, ni_mon_thread.1917 >>> wifi0 is unplug!
_nav_ci_info_init() call x_ci_reg_nfy().....................
<nav ci> _ci_init Country: RUS
{CACP}{info}[ ca_svl_builder.c][ 270] open_builder:[hdl:0x1015362][tuner:tuner_ter_dig_0]
{CACP}{info}[ ca_svl_builder.c][ 270] open_builder:[hdl:0x1015357][tuner:tuner_cab_dig_0]
{CACP}{info}[ ca_svl_builder.c][ 270] open_builder:[hdl:0x101534c][tuner:tuner_sat_dig_0]
[INET] 11.874, x_net_ni_reg_ev_notify.2015 >>> dev: eth0->eth0, event: 3, ipchg
[INET] 11.875, x_net_ni_reg_ev_notify.2015 >>> dev: eth0->eth0, event: 2, unplug
[INET] 11.875, x_net_ni_reg_ev_notify.2015 >>> dev: wifi0->wifi0, event: 3, ipchg
[INET] 11.875, x_net_ni_reg_ev_notify.2015 >>> dev: wifi0->wifi0, event: 2, unplug
[NAV_OPTION_LIST_CUSTOM.C] nav_option_list_custom_get_be_netfilx_or_not and bool_is_in_netflix_mode = 0 at line 4770
ci reg sbtl nfy.
ci reg sbtl nfy, i4_ret:0
-----------vHdmiSetARCOnOff(0)--------------
[dtv_app_mtk]>[_nav_ttx_init][2555] init teletext view 0.
[MHEG5 NVM] DVP_DirectoryOpen()
[MHEG5_NVM]mheg5 root path = /3rd_rw/mh5n, ps_full_path = /3rd_rw/mh5n/
[MHEG5 NVM] DVP_DirectoryOpen() failed as -6
[MHEG5 NVM] DVP_FileSize(NVMSTORE.dat, 0x7d069c34)
[MHEG5_NVM]mheg5 root path = /3rd_rw/mh5n, ps_full_path = /3rd_rw/mh5n/NVMSTORE.dat
[DRV_INTERFACE] Set Operation Error. (-16)
[ ACFG_CUST] c_scc_vid_set_game_mode, OFF
[LINUX_FAKE_API] sys_overscan_mode_sync
[NAV_OPTION_LIST_CUSTOM.C] nav_option_list_custom_get_be_netfilx_or_not and bool_is_in_netflix_mode = 0 at line 4770
[NAV_OPTION_LIST_CUSTOM.C] nav_option_list_custom_get_be_netfilx_or_not and bool_is_in_netflix_mode = 0 at line 4770
[INET] 12.277, ni_mon_thread.1917 >>> wifi0 is unplug!
[INET] 12.278, ni_mon_thread.1917 >>> eth0 is unplug!
nav model channel id: 2883713, pre channel:262273
nav model i4_ret: 0, b ci service:0
<ACFG> Open audio outport: 0 ms
reason: 0x00000006 - 0x00000000
[dtv_app_mtk]>[NAV]SVL_ID= 1, ui_tuner_type = 0, ui1_svl_lst_idx = 0 @Func = _ctrl_update_tv_src_info
[NAV]SVL_ID= 1, ui_tuner_type = 0, ui1_svl_lst_idx = 0 @Func = nav_get_svl_handle
[dtv_app_mtk]>ifconfig: SIOCGIFFLAGS: No such device
recovery netwokring
[dtv_app_mtk]>[_nav_cec_otp_handle_msg][1099]NAV_UI_MSG_POWER_ON.
reason: 0x00000006 - 0x00000000
[dtv_app_mtk]>[_nav_cec_otp_handle_msg][1115] TV wakes up reason 6.
[_nav_cec_sys_info_handle_msg] [648]:POWER UP TV.
Init Digital output level success.[DRV_INTERFACE] Get Operation Error. (-16)
[D-interface return ERROR] [DRV_CUSTOM_CUST_GET_SPEC_GPIO_ID] i4_ret = -16
[D-interface Warning] [DRV_CUSTOM_CUST_GET_SPEC_GPIO_ID] e_gpio_type=[2], get GPIO_ID = 0
GPIO = 0 Output 1
[dtv_app_mtk]> GPIO pin number invalid.
[dtv_app_mtk]> [BGM_OAD_DTC] _oad_detect_handle_msg :13
[dtv_app_mtk]>[BGM_OAD_DLD] _oad_download_handle_msg, it will not process any message
[dtv_app_mtk]>
[!!!Return fail:nav_cec_util.c:nav_cec_util_is_amp_exist:669:-13]
reason: 0x00000006 - 0x00000000
[dtv_app_mtk]>reason: 0x00000006 - 0x00000000
[dtv_app_mtk]>
a_xtv_power_status_onchgnfy .
[dtv_app_mtk]>
power state: 0.
[dtv_app_mtk]>
_xtv_onchangenotify Nfy Change type:2 .
[dtv_app_mtk]>
_xtv_onchangenotify Nfy Change ret:0 .
reason: 0x00000006 - 0x00000000
[dtv_app_mtk]>[a_cfg_custom_bds_update_mutirc_state] state = 0
reason: 0x00000006 - 0x00000000
[dtv_app_mtk]>[MISC] pcl wakeup reason: 6
[NAV]SVL_ID= 1, ui_tuner_type = 0, ui1_svl_lst_idx = 0 @Func = nav_get_crnt_svl_handle
reason: 0x00000006 - 0x00000000
[dtv_app_mtk]>[_nav_cec_routing_ctrl_handle_msg][1519] NAV_UI_MSG_APP_RESUMED.
ci_oceanblue_set_ts_on_off,b_on is 1
inpSrc[2]mtk]>
Resend current pmt due to change to DTV source start
Resend current pmt due to change to DTV source end
[NAV]SVL_ID= 1, ui_tuner_type = 0, ui1_svl_lst_idx = 0 @Func = nav_get_crnt_svl_handle
reason: 0x00000006 - 0x00000000
[dtv_app_mtk]>[NAV]SVL_ID= 1, ui_tuner_type = 0, ui1_svl_lst_idx = 0 @Func = nav_get_crnt_svl_handle
[Info] 0 == 0 !!!!!!!!!!!!!!!!!!!!!!!!!! [nav_event_info_view.c][ 1027]
[NAV WFD] NAV_UI_MSG_BEFORE_SVC_CHANGE RTSP status 0.
{APP_TV} TV Brdcst type = 2 TV_SCART Enabled: 1 Monitor_SCART Enabled: 0
[LINUX_FAKE_API] d_custom_get_custom_mode
[WFD]NAV_UI_MSG_APP_RESUMED .
[DRV_INTERFACE] Set Operation Error. (-16)
[ ACFG_CUST] c_scc_vid_set_game_mode, OFF
<MSCVT>Call function : a_msg_convert_register.
_nav_cec_misc_icl_nfy_func.
[_nav_cec_misc_icl_nfy_func][402]notify ID is dismatch.
reason: 0x00000006 - 0x00000000
[dtv_app_mtk]>[_nav_cec_routing_info_timer_msg_hdlr][481]Wait for RI timeout: ui2_last_route_pa = 0x0
[NAV]SVL_ID= 1, ui_tuner_type = 0, ui1_svl_lst_idx = 0 @Func = _ctrl_update_tv_src_info
[NAV]SVL_ID= 1, ui_tuner_type = 0, ui1_svl_lst_idx = 0 @Func = _ctrl_update_tv_src_info
<MSCVT>Call function _mc_app_init_fct.
@@@@@@Benson debug message:nav_ctrler.c,nav_handle_msg,8876
msg_convert_custom_init
<MSCVT> msgconvert custom: do something before init
<MSCVT>language is AUS
<MSCVT>country is RUS
reason: 0x00000006 - 0x00000000
[dtv_app_mtk]>**********DirectFBInit()
[dtv_app_mtk]>
[dtv_app_mtk]> [RHXTV] c_rpc_reg_xtvapi_op_hndlrs
[dtv_app_mtk]>c_rpc_reg_stvapi_op_hndlrs
[dtv_app_mtk]>c_rpc_reg_stvapi_chlist_op_hndlrs
[dtv_app_mtk]>SC_FCT_0: sched_getparam 509 error -1
[dtv_app_mtk]>SC_FCT_0: sched_getparam 511 error -1
[dtv_app_mtk]>[_TunerNotifyInitThread:229] Register Tuner component Fail!
[dtv_app_mtk]>[_TunerNotifyTunerProc:266] Register Tuner component excl list Fail!
[dtv_app_mtk]>[_TunerNotifyTunerProc:266] Register Tuner component excl list Fail!
[dtv_app_mtk]>[_TunerNotifyInitThread:229] Register Tuner component Fail!
[dtv_app_mtk]>[_TunerNotifyInitThread:229] Register Tuner component Fail!
[dtv_app_mtk]>[_TunerNotifyInitThread:229] Register Tuner component Fail!
[dtv_app_mtk]>[_TunerNotifyTunerProc:266] Register Tuner component excl list Fail!
[dtv_app_mtk]>[_TunerNotifyTunerProc:266] Register Tuner component excl list Fail!
[dtv_app_mtk]>[_TunerNotifyTunerProc:266] Register Tuner component excl list Fail!
[dtv_app_mtk]>[MTCI0] MTCI_Init : 0
[dtv_app_mtk]>**********DirectFBInit()
[dtv_app_mtk]>[* GL DFB *] Create plane (ON layer) :1016498
[dtv_app_mtk]>[* GL DFB *] Create plane (ON window (Shared)) :1016496
[dtv_app_mtk]>{IOM} UART thread inited.
[dtv_app_mtk]>MTDRVCUST_dcustom_misc_set() fail, ret=-1
[dtv_app_mtk]>MTDRVCUST_dcustom_misc_set() fail, ret=-1
[dtv_app_mtk]>gl_dfb_plane_open want plane 1
[dtv_app_mtk]>gl_dfb_plane_enum want plane 0
[dtv_app_mtk]>gl_dfb_plane_open want plane 0
[dtv_app_mtk]> Set color key to [0,0,0]
[dtv_app_mtk]>MTDRVCUST_dcustom_cust_spec_get() fail, ret=-1
[dtv_app_mtk]>MTDRVCUST_dcustom_vid_set() fail, ret=-1
[dtv_app_mtk]>gl_dfb_plane_open want plane 1
[dtv_app_mtk]>gl_dfb_plane_open want plane 1
[dtv_app_mtk]>MTRM_Direct_Call() fail, ret=-14
[dtv_app_mtk]>MTDRVCUST_dcustom_vid_set() fail, ret=-1
[dtv_app_mtk]>MTDRVCUST_dcustom_cust_spec_get() fail, ret=-1
[dtv_app_mtk]>MTDRVCUST_dcustom_misc_set() fail, ret=-1
[dtv_app_mtk]>MTDRVCUST_dcustom_vid_set() fail, ret=-1
[dtv_app_mtk]>[1533:IMnettvP_Ipepg_Otg_EnableDisable]> [P]========>>Calling API IMnettvP_Ipepg_Otg_EnableDisable param = [1]
[dtv_app_mtk]>[NETTV][M]>>>>>>>>>>[RemoteControlListener.cpp][239], RemoteControlListener()
[dtv_app_mtk]>[NAV]SVL_ID= 1, ui_tuner_type = 0, ui1_svl_lst_idx = 0 @Func = nav_get_crnt_svl_handle
[GCC_OSRC] osrc hide
[NAV]SVL_ID= 1, ui_tuner_type = 0, ui1_svl_lst_idx = 0 @Func = nav_get_crnt_svl_handle
[NAV]SVL_ID= 1, ui_tuner_type = 0, ui1_svl_lst_idx = 0 @Func = nav_get_crnt_svl_handle
[NAV]SVL_ID= 1, ui_tuner_type = 0, ui1_svl_lst_idx = 0 @Func = nav_get_crnt_svl_handle
[dtv_app_mtk]>[NETTV][M]>>>>>>>>>>[RemoteControlListener.cpp][87], Run() RemoteControlListener Thread Started
### osd show ###
gl_dfb_plane_open want plane 1
[dtv_app_mtk]>**********DirectFBInit()
[dtv_app_mtk]>[NETTV:10:55:59]!=!=!=!===========DfbLayerControl Constructor
[dtv_app_mtk]>
[dtv_app_mtk]>[Nav ci] _ci_nw_nfy_hdlr notify net unplug wireless0
[Nav ci] _ci_nw_nfy_hdlr notify net unplug etho
_input_cec_nfy_handler()
ui1_num: 0tk]>
ui1_num: 0tk]>
[dtv_app_mtk]>
[ 20.794432] ===============
[ 20.794437] DVBT2_TunerSetAttribute
[ 20.794441] , e_set_type = 283
[ 20.829021] [PCMCIA]PATCH_FOR_NEOTION_MACRO_BLOCK patch enable, demod TS disable
[ 20.833650] ===============
[ 20.833655] DVBT2_TunerSetAttribute
[ 20.833659] , e_set_type = 283
[ 20.873349] [PCMCIA]PATCH_FOR_NEOTION_MACRO_BLOCK patch enable, demod TS enable
[dtv_app_mtk]>a_cfg_custom_is_Russia_model FALSE
[dtv_app_mtk]>{wzd} register dt notify callback
catach length sucess.
catach length sucess.
catach length sucess.
catach length sucess.
catach length sucess.
catach length sucess.
[PHM_UPG] _phm_upg_init_fct, 201012101907:TTTTTTTTTTTTTTTTT<PHM_NWZD> _phm_nwzd_init_fct
<PHM_NWZD> _phm_nwzd_model_reset
c_ci_get#CI_GET_TYPE_SLOT_NUM
c_ci_get#CI_GET_TYPE_SLOT_INFO
Eric,Tsai-------------- _phm_usb_hid_init_fct 1
[dtv_app_mtk]>
========APP_CFG_RECID_CUST_KB_INSERT set value : 0, =========
[dtv_app_mtk]>
========APP_CFG_RECID_CUST_KB_INSERT set value : 0, =========
[ONE_CHLIST]: <a_ch_channel_list_init>
[ONE_CHLIST]: One Channel List: OFF
[dtv_app_mtk]>
[dtv_app_mtk]>
[dtv_app_mtk]>:dtv_app_mtk,am,:started=factory
[dtv_app_mtk]>
[dtv_app_mtk]># mount perm
[ 21.983814] UBI: attaching mtd11 to ubi2
[ 21.984998] UBI: save scan info advance: 1
[ 21.990046] UBI: physical eraseblock size: 131072 bytes (128 KiB)
[ 21.998205] UBI: logical eraseblock size: 126976 bytes
[ 22.001030] UBI: smallest flash I/O unit: 2048
[ 22.005975] UBI: VID header offset: 2048 (aligned 2048)
[ 22.012074] UBI: data offset: 4096
[ 22.026580] UBI: scan info block is a empty block
[dtv_app_mtk]>[_nav_cec_ro[ 22.030858] UBI: ubi get sid err[-22]
uting_ctrl_mw_nfy_hdlr_fct][1720] MW fakes this OPCODE
[_nav_cec_routing_ctrl_mw_opcode_hdlr][1174] SAC has [ 22.047143] UBI: max. sequence number: 30625
sent <routing change>.
[dtv_app_mtk]>
[!!!R[ 22.056040] UBI: attached mtd11 to ubi2
[ 22.059451] UBI: MTD device name: "perm"
[ 22.064290] UBI: MTD device size: 5 MiB
[ 22.069319] UBI: number of good PEBs: 39
[ 22.074525] UBI: number of bad PEBs: 0
[ 22.077779] UBI: number of corrupted PEBs: 0
[ 22.083058] UBI: max. allowed volumes: 128
[ 22.087382] UBI: wear-leveling threshold: 4096
[ 22.091567] UBI: number of internal volumes: 1
[ 22.096572] UBI: number of user volumes: 1
[ 22.102056] UBI: available PEBs: 0
[ 22.104956] UBI: total number of reserved PEBs: 39
[ 22.109922] UBI: number of PEBs reserved for bad PEB handling: 5
[ 22.116146] UBI: max/mean erase counter: 1119/785
[ 22.120305] UBI: image sequence number: 313261675
[ 22.125273] UBI: background thread "ubi_bgt2d" started, PID 778
eturn fail:nav_cec_sys_info.c:_nav_cec_sys_info_mw_opcode_hdlr:585:1]
UBI device number 2, total 39 LEBs (4952064 bytes, 4.7 MiB), available 0 LEBs (0 bytes), LEB size 126976 bytes (124.0 KiB)
[ 22.161872] UBIFS: recovery needed
[ 22.231217] UBIFS: recovery completed
[ 22.232620] UBIFS: mounted UBI device 2, volume 0, name "perm"
[ 22.238672] UBIFS: file system size: 2539520 bytes (2480 KiB, 2 MiB, 20 LEBs)
[ 22.245408] UBIFS: journal size: 1142785 bytes (1116 KiB, 1 MiB, 8 LEBs)
[ 22.252939] UBIFS: media format: w4/r0 (latest is w4/r0)
[ 22.258329] UBIFS: default compressor: lzo
[ 22.262327] UBIFS: reserved for root: 0 bytes (0 KiB)
[dtv_app_mtk]>[FM-Linux]Mount /dev/mtd11 to /perm successfully.
[FM](/dev/mtd11) is mounted to (/perm) successfully(0)
# mount 3rdb DMVERITY(SquashFS read-only)
[ 22.422092] /dev/mtdblock10: NFSB header found and verified.
[ 22.428325] device-mapper: verity: dev:mtdblock10 hash:mtdblock10 [sectors:584 blocks:18229]
[ 22.434903] device-mapper: table: 254:1: adding target device (start sect 0 len 145832) caused an alignment inconsistency
[dtv_app_mtk]>[DM]status changed:device path:/block/dm-1
[DM]_dm_check_device_changed entered(changed device path:/block/dm-1)...
[DM]_dm_check_device_changed exited(changed device path:/block/dm-1)...
[DM]No dev name found.
[DM]status changed:device path:/block/dm-1
[DM]_dm_check_device_changed entered(changed device path:/block/dm-1)...
[DM]_dm_check_device_changed exited(changed device path:/block/dm-1)...
[DM]No dev name found.
[dtv_app_mtk]>real 0m 0.04s
[dtv_app_mtk]>user 0m 0.00s
[dtv_app_mtk]>sys 0m 0.00s
[FM](/dev/mtdblock10) is mounted to (/3rd) unsuccessfully(-6)
MHEG5 TPS start to setup
[MHEG5_NVM]rw root path = /3rd_rw
MHEG5 TPS setup failed to create dir(-6)
# mount 3rd_rw
[ 22.615898] UBI: attaching mtd12 to ubi4
[ 22.617082] UBI: save scan info advance: 1
[ 22.622255] UBI: physical eraseblock size: 131072 bytes (128 KiB)
[ 22.627917] UBI: logical eraseblock size: 126976 bytes
[ 22.633442] UBI: smallest flash I/O unit: 2048
[ 22.637790] UBI: VID header offset: 2048 (aligned 2048)
[ 22.646216] UBI: data offset: 4096
[ 22.657875] UBI: scan info block is a empty block
[ 22.660294] UBI: ubi get sid err[-22]
[ 23.075608] UBI: max. sequence number: 35152
[ 23.088769] UBI: attached mtd12 to ubi4
[ 23.089877] UBI: MTD device name: "3rd_rw"
[ 23.095359] UBI: MTD device size: 120 MiB
[ 23.100189] UBI: number of good PEBs: 959
[ 23.104963] UBI: number of bad PEBs: 0
[ 23.109448] UBI: number of corrupted PEBs: 0
[ 23.113700] UBI: max. allowed volumes: 128
[ 23.117868] UBI: wear-leveling threshold: 4096
[ 23.123709] UBI: number of internal volumes: 1
[ 23.127001] UBI: number of user volumes: 1
[ 23.132670] UBI: available PEBs: 0
[ 23.136490] UBI: total number of reserved PEBs: 959
[ 23.140765] UBI: number of PEBs reserved for bad PEB handling: 9
[ 23.147004] UBI: max/mean erase counter: 41/37
[ 23.151419] UBI: image sequence number: 169114786
[ 23.156320] UBI: background thread "ubi_bgt4d" started, PID 810
[dtv_app_mtk]>UBI device number 4, total 959 LEBs (121769984 bytes, 116.1 MiB), available 0 LEBs (0 bytes), LEB size 126976 bytes (124.0 KiB)
[ 23.202770] UBIFS: recovery needed
[ 23.275273] UBIFS: recovery completed
[ 23.276200] UBIFS: mounted UBI device 4, volume 0, name "3rd_rw"
[ 23.282602] UBIFS: file system size: 118722560 bytes (115940 KiB, 113 MiB, 935 LEBs)
[ 23.290420] UBIFS: journal size: 9023488 bytes (8812 KiB, 8 MiB, 72 LEBs)
[ 23.297762] UBIFS: media format: w4/r0 (latest is w4/r0)
[ 23.305327] UBIFS: default compressor: lzo
[ 23.307237] UBIFS: reserved for root: 0 bytes (0 KiB)
[dtv_app_mtk]>[FM-Linux]Mount /dev/mtd12 to /3rd_rw successfully.
[FM](/dev/mtd12) is mounted to (/3rd_rw) successfully(0)
MHEG5 TPS start to setup
[MHEG5_NVM]rw root path = /3rd_rw
[MHEG5_NVM]created mheg5 root path = /3rd_rw/mh5n
MHEG5 TPS setup OK
# mount 3rd_ro
[ 23.450256] UBI: attaching mtd13 to ubi3
[ 23.451443] UBI: save scan info advance: 1
[ 23.456961] UBI: physical eraseblock size: 131072 bytes (128 KiB)
[ 23.462352] UBI: logical eraseblock size: 126976 bytes
[ 23.467609] UBI: smallest flash I/O unit: 2048
[ 23.474079] UBI: VID header offset: 2048 (aligned 2048)
[ 23.481726] UBI: data offset: 4096
[ 23.493032] UBI: scan info block is a empty block
[ 23.495092] UBI: ubi get sid err[-22]
[ 23.582351] UBI: max. sequence number: 2
[ 23.596870] UBI: attached mtd13 to ubi3
[ 23.597929] UBI: MTD device name: "ro_data"
[ 23.609188] UBI: MTD device size: 30 MiB
[ 23.614275] UBI: number of good PEBs: 239
[ 23.618608] UBI: number of bad PEBs: 0
[ 23.622147] UBI: number of corrupted PEBs: 0
[ 23.629091] UBI: max. allowed volumes: 128
[ 23.630928] UBI: wear-leveling threshold: 4096
[ 23.637428] UBI: number of internal volumes: 1
[ 23.640489] UBI: number of user volumes: 1
[ 23.644656] UBI: available PEBs: 0
[ 23.649400] UBI: total number of reserved PEBs: 239
[ 23.654108] UBI: number of PEBs reserved for bad PEB handling: 5
[ 23.660706] UBI: max/mean erase counter: 1/0
[ 23.664070] UBI: image sequence number: 777810414
[ 23.669229] UBI: background thread "ubi_bgt3d" started, PID 827
[dtv_app_mtk]>UBI device number 3, total 239 LEBs (30347264 bytes, 28.9 MiB), available 0 LEBs (0 bytes), LEB size 126976 bytes (124.0 KiB)
[ 23.726128] UBIFS: mounted UBI device 3, volume 0, name "3rd_ro"
[ 23.729446] UBIFS: mounted read-only
[ 23.733248] UBIFS: file system size: 27934720 bytes (27280 KiB, 26 MiB, 220 LEBs)
[ 23.743330] UBIFS: journal size: 4063232 bytes (3968 KiB, 3 MiB, 32 LEBs)
[ 23.747886] UBIFS: media format: w4/r0 (latest is w4/r0)
[ 23.754713] UBIFS: default compressor: lzo
[ 23.757780] UBIFS: reserved for root: 0 bytes (0 KiB)
[dtv_app_mtk]>[FM-Linux]Mount /dev/mtd13 to /3rd_ro successfully.
[FM](/dev/mtd13) is mounted to (/3rd_ro) successfully(0)
reason: 0x00000006 - 0x00000000
[dtv_app_mtk]>
[dtv_app_mtk]>_nav_cec_misc_icl_nfy_func.
_nav_cec_misc_3rd_chg_hdlr.
t_change_info.s_org_app_id is dtv_app_mtk, org app status 1 ,focus app id dtv_app_mtk.
[_nav_cec_misc_3rd_chg_hdlr][352] display ui 0.
[_nav_cec_misc_3rd_chg_hdlr][368] ui 0.
[ ACFG_CUST]: t_change_info:
[dtv_app_mtk]> s_org_app_id:dtv_app_mtk
[dtv_app_mtk]> ui1_org_app_status:1
[dtv_app_mtk]> s_focus_app_id:dtv_app_mtk
_input_cec_nfy_handler()
ui1_num: 0tk]>
ui1_num: 0tk]>
[ 24.245123] rtusb init rtusbSTA --->
[ 24.246777]
[ 24.246781]
[ 24.246784] === pAd = e05e6000, size = 1053344 ===
[ 24.246788]
[ 24.256014] <-- RTMPAllocAdapterBlock, Status=0
[ 24.259889] Efuse Size=0x2d [2d0-2fc]
[ 24.263550] NVM is EFUSE
[ 24.266827] usbcore: registered new interface driver rtusbSTA
[ 24.534612] NTFS driver 2.1.30 [Flags: R/O MODULE].
[ 24.573559] usbcore: registered new interface driver usbhid
[ 24.576709] usbhid: USB HID core driver
[dtv_app_mtk]>mount: mounting none on /proc/bus/usb failed: Device or resource busy
[INET] 18.915, ni_mon_thread.1861 >>> ra0 is plug!
[ 24.625791] v4l2_common: Unknown symbol v4l2_ctrl_get_menu (err 0)
[ 24.629700] v4l2_common: Unknown symbol v4l2_ctrl_fill (err 0)
[dtv_app_mtk]>insmod: can't insert '/basic/modules/v4l2-common.ko': unknown symbol in module or invalid parameter
[ 24.670347] Linux video capture interface: v2.00
[ 24.686672] usbcore: registered new interface driver uvcvideo
[ 24.690502] USB Video Class driver (v1.1.0)
[ 24.704150] !@#!@# @@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@ alsa_card_mtk_init 201202101600
_input_cec_nfy_handler()
ui1_num: 0tk]>
ui1_num: 0tk]>
[_nav_cec_sys_app_mw_msg_hdlr] [1096]:Export Activities.
[_nav_cec_sys_app_export_activities][405]Active source la 1.
[_nav_cec_sys_app_export_activities][405]Active source la 2.
[_nav_cec_sys_app_export_activities][405]Active source la 3.
[_nav_cec_sys_app_export_activities][405]Active source la 4.
[_nav_cec_sys_app_export_activities][405]Active source la 5.
[ 25.394296] ===============
[ 25.394301] DVBT2_TunerSetAttribute
[ 25.394305] , e_set_type = 283
[ 25.428926] [PCMCIA]PATCH_FOR_NEOTION_MACRO_BLOCK patch enable, demod TS disable
[ 25.433552] ===============
[ 25.433557] DVBT2_TunerSetAttribute
[ 25.433561] , e_set_type = 283
[_nav_cec_sys_app_export_activities][405]Active source la 6.
[ 25.473307] [PCMCIA]PATCH_FOR_NEOTION_MACRO_BLOCK patch enable, demod TS enable
[_nav_cec_sys_app_export_activities][405]Active source la 7.
[_nav_cec_sys_app_export_activities][405]Active source la 8.
[_nav_cec_sys_app_export_activities][405]Active source la 9.
**********DirectFBInit()
[dtv_app_mtk]>gl_dfb_plane_open want plane 1
[dtv_app_mtk]>gl_dfb_plane_open want plane 1
[dtv_app_mtk]>gl_dfb_plane_enum want plane 0
[dtv_app_mtk]>[NETTV][M]>>>>>>>>>>[TvControl.cpp][559], setLanguage() : Invoke IMnettvP_UserChangedLanguage, 4
[dtv_app_mtk]>gl_dfb_plane_open want plane 0
[dtv_app_mtk]>gl_dfb_plane_open want plane 2
[dtv_app_mtk]>gl_dfb_plane_open want plane 1
[dtv_app_mtk]>gl_dfb_plane_open want plane 1
[dtv_app_mtk]>[NETTV][M]>>>>>>>>>>[TvControl.cpp][724], setCountry() : Invoke IMnettvP_UserChangedCountry, RU
[dtv_app_mtk]>[ipepgmw_epgctl_set_day_time_saving:606]>
[dtv_app_mtk]>[606:IMnettvP_UserChangedLanguage]> [P]========>>User Language=en
[dtv_app_mtk]>[729:IMnettvP_UserChangedCountry]> [P]========>> change to country: RU
[dtv_app_mtk]>[ipepgmw_epgctl_set_time_zone:611]>
[dtv_app_mtk]>[1343:IMnettvP_Ipepg_SetDayTimeSaving]> [P]========>>DayTimeSaving = 0
[dtv_app_mtk]>[694:nettvapp_SetDayTimeSaving]> DayTimeSaving =0
[dtv_app_mtk]>
[dtv_app_mtk]>[NETTV][M]>>>>>>>>>>[TvControl.cpp][807], setConnectionType() : Invoke IMnettvP_Ipepg_SetConnectionType ui1_type = 5, ui2_svl_id=1
[dtv_app_mtk]>[ipepgmw_epgctl_set_connection_type:625]>
[dtv_app_mtk]>[1349:IMnettvP_Ipepg_SetTimeZone]> [P]========>>TimeZone = 10800
[dtv_app_mtk]>[709:nettvapp_SetTimeZone]> TimeZone =10800
[dtv_app_mtk]>
[dtv_app_mtk]>[NETTV][M]>>>>>>>>>>[TvControl.cpp][883], setTimeSaving() Invoke IMnettvP_Ipepg_SetDayTimeSaving 0
[dtv_app_mtk]>[ipepgmw_epgctl_set_day_time_saving:606]>
[dtv_app_mtk]>[1361:IMnettvP_Ipepg_SetConnectionType]> [P]========>>Connection Type =
[dtv_app_mtk]>[743:nettvapp_SetConnectionType]> type =
[dtv_app_mtk]>
[dtv_app_mtk]>[NETTV][M]>>>>>>>>>>[TvControl.cpp][897], setRegion() : Invoke IMnettvP_Ipepg_SetRegion, 1
[dtv_app_mtk]>[ipepgmw_epgctl_set_region:616]>
[dtv_app_mtk]>[1343:IMnettvP_Ipepg_SetDayTimeSaving]> [P]========>>DayTimeSaving = 0
[dtv_app_mtk]>[694:nettvapp_SetDayTimeSaving]> DayTimeSaving =0
[dtv_app_mtk]>
[dtv_app_mtk]>[ipepgmw_epgctl_set_region_to_shmemory:1288]>
[dtv_app_mtk]>[1355:IMnettvP_Ipepg_SetRegion]> [P]========>>Region = 1
[dtv_app_mtk]>[726:nettvapp_SetRegion]> region =1
[dtv_app_mtk]>
[dtv_app_mtk]>[1613:IMnettvP_DB_InformBcNetworkOperator]> [P]========>>
[dtv_app_mtk]>[205:_imnettv_copydata]> [P]========>>copy data files from /usr/opera/opera_home to /tmp/opera_home success
[dtv_app_mtk]>mkdir: cannot create directory '/tmp/opera_home': File exists
[dtv_app_mtk]>cp: omitting directory '/usr/opera/opera_home/handlers'
[dtv_app_mtk]>[_nav_cec_sys_app_export_activities][405]Active source la 10.
[dtv_app_mtk]>cp: omitting directory '/usr/opera/opera_home/plugins'
[208:_imnettv_copydata]> [P]========>>copy opera data files from /mnt/broser to /tmp/opera_home success
[dtv_app_mtk]>[212:_imnettv_copydata]> [P]========>>copy opera pem files from /mnt/broser to /tmp/ success
[dtv_app_mtk]>[_nav_cec_sys_app_export_activities][405]Active source la 11.
[dialserver]>
[ 28.541259] pgd = dd0b0000
[ 28.541292] [987a0000] *pgd=1b789831, *pte=00000000, *ppte=00000000
[ 28.547444]
[ 28.548999] Pid: 763, comm: nettv
[ 28.553870] CPU: 0 Tainted: P (3.0.13 #1)
[ 28.558879] PC is at 0x4409c2c0
[ 28.561951] LR is at 0x40cd3b98
[ 28.565120] pc : [<4409c2c0>] lr : [<40cd3b98>] psr: 20000010
[ 28.565126] sp : 52045aa0 ip : 00000000 fp : 52045c04
[ 28.576824] r10: 00000401 r9 : 1b0f1dc0 r8 : a2649ccb
[ 28.581784] r7 : 00000000 r6 : 40c06b7c r5 : 1b0f21f1 r4 : 0162c878
[ 28.588320] r3 : 987a0000 r2 : 04cfa1e9 r1 : 00000000 r0 : 823a8000
[ 28.595087] Flags: nzCv IRQs on FIQs on Mode USER_32 ISA ARM Segment user
[ 28.601999] Control: 10c53c7d Table: 1d0b0059 DAC: 00000015
window size: 1
window 0: [0x2022e800], 0 type :0
[AppManager:removeFocusProc]no more proc[ 28.716692] Restarting system.
Boot-
DRAM Channel A Calibration.
---и повторяется---
DRAM Channel A Calibration.
Byte 0 : Gating(2 ~ 77), Size=76, Mid=41, Set=41.
Byte 1 : Gating(2 ~ 67), Size=66, Mid=36, Set=36.
Byte 2 : Gating(2 ~ 72), Size=71, Mid=39, Set=39.
Byte 3 : Gating(2 ~ 72), Size=71, Mid=39, Set=39.
Byte 0 : DQS(8 ~ 43), Size 36, Set 24.
Byte 1 : DQS(8 ~ 43), Size 36, Set 23.
Byte 2 : DQS(6 ~ 44), Size 39, Set 23.
Byte 3 : DQS(12 ~ 41), Size 30, Set 22.
DRAM A Size = 1024 Mbytes.
Boot
Start Pmain
0x0000a000
Nand boot
NID=0x1590dc98
LZHS addr:0x00100040
LZHS size:0x001f9470
LZHS checksum:0x00000038
Boot
Start Lmain
MT5880 Boot Loader v1.11
SIF_Master0: new design
Boot reason: A/C power on!!
[PDWNC] PDWNC_PHILIPS_ReadWakeupReason: 6 (status 0x0)
-------------use external edid, disable internal edid------------------
IR DATA register : 0x 0
T8032 init A/C on case loader stage...
Load T8032 FW (addr: 0x d454f8, size: 24286)success!!
T8032 FW version: 20
T8032 change to loader stage...
LDR_FlashCopy 0xf010 0x73800 0x80
Detect NAND flash ID: 0x1590DC98
Detect TC58NVG2S3ETA00/I0 NAND flash(SLC): 512MB
NAND_BDM_Mount: Partid=0, offset=0x0, size=0x200000
NAND_BDM_Mount: Partid: 0, Total Block Count: 16, Bad Block Count: 0
1st MAC in EEP is valid (1c:5a:6b:40:bd:b7)
1st : (1c:5a:6b:40:bd:b7)
2nd : (1c:5a:6b:40:bd:b7)
[PDWNC] Current state : 0x1
[PDWNC]PDWNC_PHILIPS_DetermineNextState : u4Event = 0x6
PDWNC_PHILIPS_DetermineNextState : u4Current = 1
PDWNC_PHILIPS_DetermineNextState : system booting
PDWNC_PHILIPS_DetermineNextState : event = PDWNC_WAKE_UP_REASON_AC_POWER
Read EEPROM OK at PDWNC_PHILIPS_GetLoungeMode
PDWNC_PHILIPS_DetermineNextState : Lounge mode = 0
Current = 0x1, Event = 0x6, Next = 0x1
[PDWNC] PDWNC_PHILIPS_EnterNextState : u4Next = 0x1
[PDWNC]PDWNC_ReadWakeupReason = 0x6
[PDWNC]Enter normal mode, LED changes to normal
PDWNC_Init
USB0: Set GPIO63 = 1.
USB1: Set GPIO64 = 1.
Display 0x00efea60 background:0x00000000
Find panel index 184 from EEPROM
OSD_SetPlaneSwitchOrder[0,1,2],Switch[1,2,3]
---------- [SA7] vErrorHandleInit ----------
[SA7] Error handling init
[SA7] PANEL_GetPanelWidth=0x556, PANEL_GetPanelHeight=0x300 , wDrvGetOutputHTotal=0x898 , wDrvGetOutputVTotal=0x465
[SA7] PANEL_GetHTotalMax=0x794, PANEL_GetHTotalMin=0x604, PANEL_GetVTotalMax=0x3cc, PANEL_GetVTotalMin=0x30a
[SA7] PANEL_GetPixelClkMax=85000000, PANEL_GetPixelClkMin=72000000
[SA7] PANEL_GetPixelClk60Hz = 0x4e27603
---------- [SA7] vErrorHandleSetByTiming ----------
[SA7] u2HSyncWidth=260, u2HSyncStart=1930, u2VSyncWidth=26, u2VSyncStart=1094
---------- [SA7] vErrorHandleSetByTiming end----------
---------- [SA7] vErrorHandleSetByPanel end----------
[SA7] vDDDSInit
---------- [SA7] vErrorHandleSetByTiming ----------
[SA7] u2HSyncWidth=30, u2HSyncStart=1382, u2VSyncWidth=3, u2VSyncStart=800
---------- [SA7] vErrorHandleSetByTiming end----------
vDrvSetOCLKClockSchemaInit.
[SA7] _fgVopllUseDDDS = True
[LVDS] VOPLL Initialize successful !
LDR_OsdDisplay(14, 0x00d66060, 1280, 291)
Color:14 BmpAddr:0x00d66060 Width:1280 Height:291
Panel 1366 x 768
*************u4BmpPitch=5120******************
Do USB upgrade
USB: Vbus turn up time = 1643 ms, Max =0 ms.
USB-0: insert.
USB-1: insert.
USB-0: ClassCode= 0x9, u4Diff=117 ms.
FIND_CLASS_HUB.
HUB No USB Medium on Hub.
USB upgrade stop
Flash load lzhs header from 0x80000 to dram(0x1526270), size=2048
Decompression uboot to 0x00800000...
Flash load image from 0x80000 to dram(0x1526270), size=0x403e6
NAND_BDM_Mount: Partid=5, offset=0x700000, size=0x400000
NAND_BDM_Mount: Partid: 5, Total Block Count: 32, Bad Block Count: 0
Flash load tz from 0x21ab97(kernel) to dram(0x3f200000), size=0x2b599
secure boot ok
secure boot ok
Starting image...
▒
U-Boot 2011.12.12 (Aug 11 2014 - 10:51:37)
DRAM: 725.3 MiB
WARNING: Caches not enabled
NAND: Detect NAND flash ID: 0x1590DC98
Detect TC58NVG2S3ETA00/I0 NAND flash: 512MB
512 MiB
0.0.0.0
In: serial
Out: serial
Err: serial
Boot from kernelB and rootfsB(partition 7)
error, env space is not enough
Net: Net Initialization Skipped
No ethernet found.
Hit any key to stop autoboot: 0
Partition rootfsA defined at mtdparts:
ID:6, Offset:0x00000000, Size:0x00b00000
Loader succeeded in signature verification
## Booting kernel from Legacy Image at 00007fc0 ...
XIP Kernel Image ... OK
OK
Starting kernel ...
TZ Heap: start=0x3FA5CC80, end=0x40000000
TZ dram: start=0x3F000000, end=0x40000000
[ 0.000000] timekeeping_init done
INIT: version 2.86 booting
Loading /etc/profile...
Start readahead /etc/readahead_early
Running rc.local...
net.ipv4.tcp_window_scaling = 6
INIT: Entering runlevel: 3
**********DirectFBInit()
commandline read: app_man
~~~~~~~~~~~~~~~~~~~~~~~~~~| DirectFB 1.4.0 |~~~~~~~~~~~~~~
(c) 2001-2009 The world wide DirectFB Open Source Community
(c) 2000-2004 Convergence (integrated media) GmbH
----------------------------------------------------------------
======DFB 3DMM u4VirtAddr : 0x3a6c5000, and DFB 3DMM u4Size : 0x1f80000======
[input_add_device][1629]
[LinuxInput_Initialize][2172]
[input_add_device][1629]
[LinuxInput_Initialize][2172]
[input_add_device][1629]
[LinuxInput_Initialize][2172]
[input_add_device][1629]
[LinuxInput_Initialize][2172]
[input_add_device][1629]
[LinuxInput_Initialize][2172]
[input_add_device][1629]
[LinuxInput_Initialize][2172]
[input_add_device][1629]
[LinuxInput_Initialize][2172]
[input_add_device][1629]
[LinuxInput_Initialize][2172]
[input_add_device][1629]
[LinuxInput_Initialize][2172]
[input_add_device][1629]
[LinuxInput_Initialize][2172]
[input_add_device][1629]
[LinuxInput_Initialize][2172]
[input_add_device][1629]
[LinuxInput_Initialize][2172]
[input_add_device][1629]
[LinuxInput_Initialize][2172]
[input_add_device][1629]
[LinuxInput_Initialize][2172]
[input_add_device][1629]
[LinuxInput_Initialize][2172]
[input_add_device][1629]
input thread's parent pid is 517 tid is 517
[LinuxInput_Initialize][2172]
[input_add_device][1629]
[DirectFB]: Wait to Init IR...!
[input_add_device][1629]
dfb_set_cursor_border [0,0,1280,0]
[dtv_app_mtk]>InitDRM
[dtv_app_mtk]>drv_init as 0x39 model
[dtv_app_mtk]>drv_init as EU model
[dtv_app_mtk]>HDMI fast booting init...
[ 9.163571] NAND_SDM_Mount: Partid=15, offset=0x1d680000, size=0x2980000
input thread pid is 517 tid is 538
original scheduler policy 0
scheduler nice 0
original child scheduler policy 0 prio 0
new child scheduler policy 2 prio 99
Start to wait IR event...
[dtv_app_mtk]>
[dtv_app_mtk]>TVD MsgCtrl: NRL:60/40, PER:100/90
[dtv_app_mtk]>x_drv_init end!!
[dtv_app_mtk]>[ FakeDM ] Init...
[FakeDM] Init FM...
/dev is created./mnt is already existed. That is OK.
/mnt/usb is created.[FakeDM] FM inited...
[FakeDM] Init SMB...
[FakeDM] SMB inited...
[FakeDM] do coldboot start...
[DM] _dm_open_dev_thread: entered
[DM] _dm_nfy_req_thread enter
[DM] _dm_nfy_req_thread get_nl_sock:25
[DM] _dm_cb_msg_thread enter
[DM] usbfs mounted.
[FakeDM] do coldboot end!!!
Init chip_spec_init!!!!!
EEPROM size is 0x4000.
{CI_glue}:ci_eng_init
{CI_glue}- expect PROD key
{CI_glue}- c[1]
88888888888888 PHYSICAL_Init() entered 888888888888888
88888888888888 ITC_Init() entered 888888888888888
88888888888888 PHYS_DRVOpen() entered 888888888888888
88888888888888 STB_CIOpen() entered 888888888888888
88888888888888 STB_CIOpen() ended 888888888888888
{CI}CI_RegInterrupt_nfy
88888888888888 PHYS_DRVOpen() entered 888888888888888
[ACFG_CUSTOM] acfg_custom_get_svl_tsl_dual_bank ui1_g_svl_tsl_dual_bank == DUAL_BANK_SVL_TSL_INVALID and get form plf is 255
[ACFG_CUSTOM] acfg_custom_get_svl_tsl_dual_bank Line 9751
[ACFG_CUSTOM] acfg_custom_get_svl_tsl_dual_bank: MAIN
{CDB} Loading metadata (version 7)
{CDB} Loading metadata (version 7)
{CDB} Loading metadata (version 7)
{CDB} Loading metadata (version 7)
{CDB} Loading metadata (version 7)
{CDB} Loading metadata (version 7)
{CDB} Loading metadata (version 7)
[dtv_app_mtk]>
[dtv_app_mtk]> ~~~~~~~~~~~~~~~~~~~~~~~~~~| DirectFB 1.4.0 |~~~~~~~~~~~~~~
[dtv_app_mtk]> (c) 2001-2009 The world wide DirectFB Open Source Community
[dtv_app_mtk]> (c) 2000-2004 Convergence (integrated media) GmbH
[dtv_app_mtk]> ----------------------------------------------------------------
[dtv_app_mtk]>
[dtv_app_mtk]>[dfb_input_core_join][974]
[dtv_app_mtk]>dfb_set_cursor_border [0,0,1280,0]
window size: 0
stacking [0x2], layer_id [0]
Init DSMCC[5][3][2]
MHEG5 TPS start to setup
[MHEG5_NVM]rw root path = /3rd_rw
MHEG5 TPS setup failed to create dir(-6)
EEPROM size is 0x70.
[dtv_app_mtk]>
[dtv_app_mtk]>
x_wifi_cli_init~~~
[dtv_app_mtk]>
[dtv_app_mtk]>
Rec_util_thread:buffer addr 0x00003d79b000,size 0x380000
{HBBTV_DSMCC} Init HBBTV DSMCC
{DT} Real Time Clock is available on this system.
EEPROM size is 0x70.
=====================
channel id:(2883713), svl rec id:(11), channel id in rec:(2883713), brdcst type:(2)
=====================
{CI}Is a CI+ CAM = 0, the mode = 0, cur mode = 0
reason: 0x00000006 - 0x00000000
[dtv_app_mtk]><AM> wakeup reason = 6
EEPROM size is 0x35b0.
EEPROM size is 0x4000.
reason: 0x00000006 - 0x00000000
[dtv_app_mtk]>[OT][_acfg_ch_lst_load_p1][723]: e_wakeup_reason = 6.
{CDB} Loading metadata (version 7)
{CDB} Loading metadata (version 7)
{CDB} Loading metadata (version 7)
{CDB} Loading metadata (version 7)
{CDB} Loading metadata (version 7)
{CDB} Loading metadata (version 7)
<PLF_OPT> Align option codes (OPC_USED[NVM] - OPC1 OPC2 OPC3)
16 _app - 16 16 16
224 _app - 224 224 224
48 _app - 48 48 48
0 _app - 0 0 0
38 _app - 38 38 38
128 _app - 128 128 128
192 _app - 192 192 192
15 _app - 15 15 15
159 _app - 159 159 159
255 _app - 255 255 255
127 _app - 127 127 127
61 _app - 61 61 61
235 _app - 235 235 235
4 _app - 4 4 4
0 _app - 0 0 0
0 _app - 0 0 0
TP vision IP SW - Mbdsl1(13.00.00.01)initializaiton-successful
reason: 0x00000006 - 0x00000000
[dtv_app_mtk]>[a_cfg_custom_bds_update_mutirc_state] state = 0
BGM: Power mgmt init
[dtv_app_mtk]>[BGM] [OTG] _bgm_otg_init
[dtv_app_mtk]>BGM: Update scan init
[dtv_app_mtk]><BGM CAM>: cam scan component init
[dtv_app_mtk]>[BGM_OAD_DTC] _oad_detect_init
[dtv_app_mtk]>[BGM_OAD_DLD] _oad_download_init
[dtv_app_mtk]>BGM: Ambilight module init
[dtv_app_mtk]>_stvapi_app_init_fct
ERR: _CHL_RCHL_RealChannelMatchT(1365): Assert(pt_realChannel->e_idType == IDType_DVBT_T)
ERR: _CHL_RCHL_RealChannelMatchT(1365): Assert(pt_realChannel->e_idType == IDType_DVBT_T)
ERR: _CHL_RCHL_RealChannelMatchT(1365): Assert(pt_realChannel->e_idType == IDType_DVBT_T)
ERR: _CHL_RCHL_RealChannelMatchT(1365): Assert(pt_realChannel->e_idType == IDType_DVBT_T)
ERR: _CHL_RCHL_RealChannelMatchT(1365): Assert(pt_realChannel->e_idType == IDType_DVBT_T)
ERR: _CHL_RCHL_RealChannelMatchT(1365): Assert(pt_realChannel->e_idType == IDType_DVBT_T)
ERR: _CHL_RCHL_RealChannelMatchT(1365): Assert(pt_realChannel->e_idType == IDType_DVBT_T)
{svl}x_svl_read_common(0x1016113)=0,size=1536
reason: 0x00000006 - 0x00000000
[dtv_app_mtk]>[NAV_OPTION_LIST_CUSTOM.C] nav_option_list_custom_get_be_netfilx_or_not and bool_is_in_netflix_mode = 0 at line 4770
<ACFG> The min/max/pos of h-pos in driver is wrong.
<ACFG> The min/max/pos of v-pos in driver is wrong.
[NAV]SVL_ID= 1, ui_tuner_type = 0, ui1_svl_lst_idx = 0 @Func = nav_sort_svl_rec
[NAV]SVL_ID= 2, ui_tuner_type = 1, ui1_svl_lst_idx = 0 @Func = nav_sort_svl_rec
Set country code to [RUS] by SB_KEY_TYPE_COUNTRY_CODE
[DRV_INTERFACE] Get Operation Error. (-16)
[D-interface return ERROR] [DRV_CUSTOM_CUST_GET_SPEC_GPIO_ID] i4_ret = -16
[D-interface Warning] [DRV_CUSTOM_CUST_GET_SPEC_GPIO_ID] e_gpio_type=[10], get GPIO_ID = 0
GPIO = 0 Output 2
[dtv_app_mtk]> GPIO pin number invalid.
[dtv_app_mtk]> ****FIX ME****, acfg_custom_post_init:8489
****FIX ME****, acfg_custom_post_init:8489
****FIX ME****, acfg_custom_post_init:8489
[DRV_INTERFACE] Set Operation Error. (-16)
[ ACFG_CUST] c_scc_vid_set_game_mode, OFF
<ACFG> set 3D nav: SEMI_AUTO, ret = 0
_edb_dvb_process_restart_edb_nfy
open root EDB_tuner_ter_dig_0
{EDB} _edb_dvb_load_table Ok!
_edb_dvb_process_restart_edb_nfy
_edb_dvb_process_restart_edb_nfy
_edb_dvb_process_restart_edb_nfy
_edb_dvb_process_restart_edb_nfy
_edb_dvb_process_restart_edb_nfy
{EDB} begin free 1 message
_edb_dvb_process_restart_edb_nfy
_edb_dvb_process_restart_edb_nfy
{EDB} begin free 1 message
{EDB} _edb_dvb_free_table Ok!
{EDB} free root Ok!
open root EDB_tuner_ter_dig_0
{EDB} _edb_dvb_load_table Ok!
[dtv_app_mtk]>
[dtv_app_mtk]>
[dtv_app_mtk]> S/W Version
[dtv_app_mtk]>
[dtv_app_mtk]> TPM1013E_003.011.000.001
[dtv_app_mtk]>
[dtv_app_mtk]> NVM Version
[dtv_app_mtk]>
[dtv_app_mtk]> 2.00
[dtv_app_mtk]>
[dtv_app_mtk]>reason: 0x00000006 - 0x00000000
[dtv_app_mtk]>{EDB} begin free 1 message
_edb_dvb_process_restart_edb_nfy
{CDB} Loading metadata (version 7)
{CDB} Loading metadata (version 7)
{CDB} Loading metadata (version 7)
_edb_dvb_process_restart_edb_nfy
{CDB} Loading metadata (version 7)
{CDB} Loading metadata (version 7)
{CDB} Loading metadata (version 7)
{CDB} Loading metadata (version 7)
{EDB} begin free 2 message
_edb_dvb_process_restart_edb_nfy
{CDB} Loading metadata (version 7)
{CDB} Loading metadata (version 7)
{EDB} begin free 2 message
{CDB} Loading metadata (version 7)
{CDB} Loading metadata (version 7)
{CDB} Loading metadata (version 7)
_edb_dvb_process_restart_edb_nfy
{CDB} Loading metadata (version 7)
{CDB} Loading metadata (version 7)
_edb_dvb_process_restart_edb_nfy
{EDB} begin free 3 message
{CDB} Loading metadata (version 7)
{CDB} Loading metadata (version 7)
_edb_dvb_process_restart_edb_nfy
{CDB} Loading metadata (version 7)
{CDB} Loading metadata (version 7)
[INET] 11.465, x_net_ip_v6_auto.4720 >>> (eth0->eth0, b_restart_if = 0
[INET] 11.466, x_net_network_reg_nfy.4297 >>> {EDB} begin free 3 message
0x410a7ff8, 0x00000000
[INET] 11.469, x_net_ni_enable.1455 >>> if enable eth0->eth0
_edb_dvb_process_restart_edb_nfy
{EDB} _edb_dvb_free_table Ok!
{EDB} free root Ok!
open root EDB_tuner_ter_dig_0
{EDB} begin free 3 message
{EDB} _edb_dvb_load_table Ok!
[NAV]SVL_ID= 1, ui_tuner_type = 0, ui1_svl_lst_idx = 0 @Func = nav_get_svl_handle
_edb_dvb_process_restart_edb_nfy
{EDB} begin free 3 message
_edb_dvb_process_restart_edb_nfy
_edb_dvb_process_restart_edb_nfy
{EDB} begin free 3 message
_edb_dvb_process_restart_edb_nfy
{EDB} begin free 4 message
_edb_dvb_process_restart_edb_nfy
{EDB} begin free 4 message
_edb_dvb_process_restart_edb_nfy
_edb_dvb_process_restart_edb_nfy
{EDB} _edb_dvb_free_table Ok!
{EDB} free root Ok!
open root EDB_tuner_ter_dig_0
{EDB} _edb_dvb_load_table Ok!
{EDB} begin free 5 message
_edb_dvb_process_restart_edb_nfy
{EDB} begin free 5 message
[INET] 11.579, x_net_network_reg_nfy.4301 >>> call eth0 enabled
_edb_dvb_process_restart_edb_nfy
_edb_dvb_process_restart_edb_nfy
{EDB} begin free 6 message
_edb_dvb_process_restart_edb_nfy
{EDB} begin free 6 message
_edb_dvb_process_restart_edb_nfy
_edb_dvb_process_restart_edb_nfy
{EDB} begin free 6 message
[NAV_OPTION_LIST_CUSTOM.C] nav_option_list_custom_get_be_netfilx_or_not and bool_is_in_netflix_mode = 0 at line 4770
{EDB} begin free 6 message
{EDB} begin free 5 message
vc_cre initk]>
vc_hiden init>
[GCC_OSRC] osrc create
{EDB} begin free 4 message
<wfd-------->>: _nav_wfd_init is called !!
[WFD MSG]Create msg notify 0x1035731
left 64 top 210.
{EDB} begin free 3 message
{EDB} begin free 2 message
{EDB} begin free 1 message
[dtv_app_mtk]>
left 64 top 253.
[dtv_app_mtk]>
left 64 top 195.
[INET] 11.758, x_net_ni_reg_ev_notify.2015 >>> dev: wifi0->wifi0, event: 1, plugin
[INET] 11.759, x_net_ni_reg_ev_notify.2015 >>> dev: wifi0->wifi0, event: 2, unplug
lru_list_create.
lru_list_create.
[INET] 11.772, ni_mon_thread.1917 >>> wifi0 is unplug!
_nav_ci_info_init() call x_ci_reg_nfy().....................
<nav ci> _ci_init Country: RUS
{CACP}{info}[ ca_svl_builder.c][ 270] open_builder:[hdl:0x1015362][tuner:tuner_ter_dig_0]
{CACP}{info}[ ca_svl_builder.c][ 270] open_builder:[hdl:0x1015357][tuner:tuner_cab_dig_0]
{CACP}{info}[ ca_svl_builder.c][ 270] open_builder:[hdl:0x101534c][tuner:tuner_sat_dig_0]
[INET] 11.874, x_net_ni_reg_ev_notify.2015 >>> dev: eth0->eth0, event: 3, ipchg
[INET] 11.875, x_net_ni_reg_ev_notify.2015 >>> dev: eth0->eth0, event: 2, unplug
[INET] 11.875, x_net_ni_reg_ev_notify.2015 >>> dev: wifi0->wifi0, event: 3, ipchg
[INET] 11.875, x_net_ni_reg_ev_notify.2015 >>> dev: wifi0->wifi0, event: 2, unplug
[NAV_OPTION_LIST_CUSTOM.C] nav_option_list_custom_get_be_netfilx_or_not and bool_is_in_netflix_mode = 0 at line 4770
ci reg sbtl nfy.
ci reg sbtl nfy, i4_ret:0
-----------vHdmiSetARCOnOff(0)--------------
[dtv_app_mtk]>[_nav_ttx_init][2555] init teletext view 0.
[MHEG5 NVM] DVP_DirectoryOpen()
[MHEG5_NVM]mheg5 root path = /3rd_rw/mh5n, ps_full_path = /3rd_rw/mh5n/
[MHEG5 NVM] DVP_DirectoryOpen() failed as -6
[MHEG5 NVM] DVP_FileSize(NVMSTORE.dat, 0x7d069c34)
[MHEG5_NVM]mheg5 root path = /3rd_rw/mh5n, ps_full_path = /3rd_rw/mh5n/NVMSTORE.dat
[DRV_INTERFACE] Set Operation Error. (-16)
[ ACFG_CUST] c_scc_vid_set_game_mode, OFF
[LINUX_FAKE_API] sys_overscan_mode_sync
[NAV_OPTION_LIST_CUSTOM.C] nav_option_list_custom_get_be_netfilx_or_not and bool_is_in_netflix_mode = 0 at line 4770
[NAV_OPTION_LIST_CUSTOM.C] nav_option_list_custom_get_be_netfilx_or_not and bool_is_in_netflix_mode = 0 at line 4770
[INET] 12.277, ni_mon_thread.1917 >>> wifi0 is unplug!
[INET] 12.278, ni_mon_thread.1917 >>> eth0 is unplug!
nav model channel id: 2883713, pre channel:262273
nav model i4_ret: 0, b ci service:0
<ACFG> Open audio outport: 0 ms
reason: 0x00000006 - 0x00000000
[dtv_app_mtk]>[NAV]SVL_ID= 1, ui_tuner_type = 0, ui1_svl_lst_idx = 0 @Func = _ctrl_update_tv_src_info
[NAV]SVL_ID= 1, ui_tuner_type = 0, ui1_svl_lst_idx = 0 @Func = nav_get_svl_handle
[dtv_app_mtk]>ifconfig: SIOCGIFFLAGS: No such device
recovery netwokring
[dtv_app_mtk]>[_nav_cec_otp_handle_msg][1099]NAV_UI_MSG_POWER_ON.
reason: 0x00000006 - 0x00000000
[dtv_app_mtk]>[_nav_cec_otp_handle_msg][1115] TV wakes up reason 6.
[_nav_cec_sys_info_handle_msg] [648]:POWER UP TV.
Init Digital output level success.[DRV_INTERFACE] Get Operation Error. (-16)
[D-interface return ERROR] [DRV_CUSTOM_CUST_GET_SPEC_GPIO_ID] i4_ret = -16
[D-interface Warning] [DRV_CUSTOM_CUST_GET_SPEC_GPIO_ID] e_gpio_type=[2], get GPIO_ID = 0
GPIO = 0 Output 1
[dtv_app_mtk]> GPIO pin number invalid.
[dtv_app_mtk]> [BGM_OAD_DTC] _oad_detect_handle_msg :13
[dtv_app_mtk]>[BGM_OAD_DLD] _oad_download_handle_msg, it will not process any message
[dtv_app_mtk]>
[!!!Return fail:nav_cec_util.c:nav_cec_util_is_amp_exist:669:-13]
reason: 0x00000006 - 0x00000000
[dtv_app_mtk]>reason: 0x00000006 - 0x00000000
[dtv_app_mtk]>
a_xtv_power_status_onchgnfy .
[dtv_app_mtk]>
power state: 0.
[dtv_app_mtk]>
_xtv_onchangenotify Nfy Change type:2 .
[dtv_app_mtk]>
_xtv_onchangenotify Nfy Change ret:0 .
reason: 0x00000006 - 0x00000000
[dtv_app_mtk]>[a_cfg_custom_bds_update_mutirc_state] state = 0
reason: 0x00000006 - 0x00000000
[dtv_app_mtk]>[MISC] pcl wakeup reason: 6
[NAV]SVL_ID= 1, ui_tuner_type = 0, ui1_svl_lst_idx = 0 @Func = nav_get_crnt_svl_handle
reason: 0x00000006 - 0x00000000
[dtv_app_mtk]>[_nav_cec_routing_ctrl_handle_msg][1519] NAV_UI_MSG_APP_RESUMED.
ci_oceanblue_set_ts_on_off,b_on is 1
inpSrc[2]mtk]>
Resend current pmt due to change to DTV source start
Resend current pmt due to change to DTV source end
[NAV]SVL_ID= 1, ui_tuner_type = 0, ui1_svl_lst_idx = 0 @Func = nav_get_crnt_svl_handle
reason: 0x00000006 - 0x00000000
[dtv_app_mtk]>[NAV]SVL_ID= 1, ui_tuner_type = 0, ui1_svl_lst_idx = 0 @Func = nav_get_crnt_svl_handle
[Info] 0 == 0 !!!!!!!!!!!!!!!!!!!!!!!!!! [nav_event_info_view.c][ 1027]
[NAV WFD] NAV_UI_MSG_BEFORE_SVC_CHANGE RTSP status 0.
{APP_TV} TV Brdcst type = 2 TV_SCART Enabled: 1 Monitor_SCART Enabled: 0
[LINUX_FAKE_API] d_custom_get_custom_mode
[WFD]NAV_UI_MSG_APP_RESUMED .
[DRV_INTERFACE] Set Operation Error. (-16)
[ ACFG_CUST] c_scc_vid_set_game_mode, OFF
<MSCVT>Call function : a_msg_convert_register.
_nav_cec_misc_icl_nfy_func.
[_nav_cec_misc_icl_nfy_func][402]notify ID is dismatch.
reason: 0x00000006 - 0x00000000
[dtv_app_mtk]>[_nav_cec_routing_info_timer_msg_hdlr][481]Wait for RI timeout: ui2_last_route_pa = 0x0
[NAV]SVL_ID= 1, ui_tuner_type = 0, ui1_svl_lst_idx = 0 @Func = _ctrl_update_tv_src_info
[NAV]SVL_ID= 1, ui_tuner_type = 0, ui1_svl_lst_idx = 0 @Func = _ctrl_update_tv_src_info
<MSCVT>Call function _mc_app_init_fct.
@@@@@@Benson debug message:nav_ctrler.c,nav_handle_msg,8876
msg_convert_custom_init
<MSCVT> msgconvert custom: do something before init
<MSCVT>language is AUS
<MSCVT>country is RUS
reason: 0x00000006 - 0x00000000
[dtv_app_mtk]>**********DirectFBInit()
[dtv_app_mtk]>
[dtv_app_mtk]> [RHXTV] c_rpc_reg_xtvapi_op_hndlrs
[dtv_app_mtk]>c_rpc_reg_stvapi_op_hndlrs
[dtv_app_mtk]>c_rpc_reg_stvapi_chlist_op_hndlrs
[dtv_app_mtk]>SC_FCT_0: sched_getparam 509 error -1
[dtv_app_mtk]>SC_FCT_0: sched_getparam 511 error -1
[dtv_app_mtk]>[_TunerNotifyInitThread:229] Register Tuner component Fail!
[dtv_app_mtk]>[_TunerNotifyTunerProc:266] Register Tuner component excl list Fail!
[dtv_app_mtk]>[_TunerNotifyTunerProc:266] Register Tuner component excl list Fail!
[dtv_app_mtk]>[_TunerNotifyInitThread:229] Register Tuner component Fail!
[dtv_app_mtk]>[_TunerNotifyInitThread:229] Register Tuner component Fail!
[dtv_app_mtk]>[_TunerNotifyInitThread:229] Register Tuner component Fail!
[dtv_app_mtk]>[_TunerNotifyTunerProc:266] Register Tuner component excl list Fail!
[dtv_app_mtk]>[_TunerNotifyTunerProc:266] Register Tuner component excl list Fail!
[dtv_app_mtk]>[_TunerNotifyTunerProc:266] Register Tuner component excl list Fail!
[dtv_app_mtk]>[MTCI0] MTCI_Init : 0
[dtv_app_mtk]>**********DirectFBInit()
[dtv_app_mtk]>[* GL DFB *] Create plane (ON layer) :1016498
[dtv_app_mtk]>[* GL DFB *] Create plane (ON window (Shared)) :1016496
[dtv_app_mtk]>{IOM} UART thread inited.
[dtv_app_mtk]>MTDRVCUST_dcustom_misc_set() fail, ret=-1
[dtv_app_mtk]>MTDRVCUST_dcustom_misc_set() fail, ret=-1
[dtv_app_mtk]>gl_dfb_plane_open want plane 1
[dtv_app_mtk]>gl_dfb_plane_enum want plane 0
[dtv_app_mtk]>gl_dfb_plane_open want plane 0
[dtv_app_mtk]> Set color key to [0,0,0]
[dtv_app_mtk]>MTDRVCUST_dcustom_cust_spec_get() fail, ret=-1
[dtv_app_mtk]>MTDRVCUST_dcustom_vid_set() fail, ret=-1
[dtv_app_mtk]>gl_dfb_plane_open want plane 1
[dtv_app_mtk]>gl_dfb_plane_open want plane 1
[dtv_app_mtk]>MTRM_Direct_Call() fail, ret=-14
[dtv_app_mtk]>MTDRVCUST_dcustom_vid_set() fail, ret=-1
[dtv_app_mtk]>MTDRVCUST_dcustom_cust_spec_get() fail, ret=-1
[dtv_app_mtk]>MTDRVCUST_dcustom_misc_set() fail, ret=-1
[dtv_app_mtk]>MTDRVCUST_dcustom_vid_set() fail, ret=-1
[dtv_app_mtk]>[1533:IMnettvP_Ipepg_Otg_EnableDisable]> [P]========>>Calling API IMnettvP_Ipepg_Otg_EnableDisable param = [1]
[dtv_app_mtk]>[NETTV][M]>>>>>>>>>>[RemoteControlListener.cpp][239], RemoteControlListener()
[dtv_app_mtk]>[NAV]SVL_ID= 1, ui_tuner_type = 0, ui1_svl_lst_idx = 0 @Func = nav_get_crnt_svl_handle
[GCC_OSRC] osrc hide
[NAV]SVL_ID= 1, ui_tuner_type = 0, ui1_svl_lst_idx = 0 @Func = nav_get_crnt_svl_handle
[NAV]SVL_ID= 1, ui_tuner_type = 0, ui1_svl_lst_idx = 0 @Func = nav_get_crnt_svl_handle
[NAV]SVL_ID= 1, ui_tuner_type = 0, ui1_svl_lst_idx = 0 @Func = nav_get_crnt_svl_handle
[dtv_app_mtk]>[NETTV][M]>>>>>>>>>>[RemoteControlListener.cpp][87], Run() RemoteControlListener Thread Started
### osd show ###
gl_dfb_plane_open want plane 1
[dtv_app_mtk]>**********DirectFBInit()
[dtv_app_mtk]>[NETTV:10:55:59]!=!=!=!===========DfbLayerControl Constructor
[dtv_app_mtk]>
[dtv_app_mtk]>[Nav ci] _ci_nw_nfy_hdlr notify net unplug wireless0
[Nav ci] _ci_nw_nfy_hdlr notify net unplug etho
_input_cec_nfy_handler()
ui1_num: 0tk]>
ui1_num: 0tk]>
[dtv_app_mtk]>
[ 20.794432] ===============
[ 20.794437] DVBT2_TunerSetAttribute
[ 20.794441] , e_set_type = 283
[ 20.829021] [PCMCIA]PATCH_FOR_NEOTION_MACRO_BLOCK patch enable, demod TS disable
[ 20.833650] ===============
[ 20.833655] DVBT2_TunerSetAttribute
[ 20.833659] , e_set_type = 283
[ 20.873349] [PCMCIA]PATCH_FOR_NEOTION_MACRO_BLOCK patch enable, demod TS enable
[dtv_app_mtk]>a_cfg_custom_is_Russia_model FALSE
[dtv_app_mtk]>{wzd} register dt notify callback
catach length sucess.
catach length sucess.
catach length sucess.
catach length sucess.
catach length sucess.
catach length sucess.
[PHM_UPG] _phm_upg_init_fct, 201012101907:TTTTTTTTTTTTTTTTT<PHM_NWZD> _phm_nwzd_init_fct
<PHM_NWZD> _phm_nwzd_model_reset
c_ci_get#CI_GET_TYPE_SLOT_NUM
c_ci_get#CI_GET_TYPE_SLOT_INFO
Eric,Tsai-------------- _phm_usb_hid_init_fct 1
[dtv_app_mtk]>
========APP_CFG_RECID_CUST_KB_INSERT set value : 0, =========
[dtv_app_mtk]>
========APP_CFG_RECID_CUST_KB_INSERT set value : 0, =========
[ONE_CHLIST]: <a_ch_channel_list_init>
[ONE_CHLIST]: One Channel List: OFF
[dtv_app_mtk]>
[dtv_app_mtk]>
[dtv_app_mtk]>:dtv_app_mtk,am,:started=factory
[dtv_app_mtk]>
[dtv_app_mtk]># mount perm
[ 21.983814] UBI: attaching mtd11 to ubi2
[ 21.984998] UBI: save scan info advance: 1
[ 21.990046] UBI: physical eraseblock size: 131072 bytes (128 KiB)
[ 21.998205] UBI: logical eraseblock size: 126976 bytes
[ 22.001030] UBI: smallest flash I/O unit: 2048
[ 22.005975] UBI: VID header offset: 2048 (aligned 2048)
[ 22.012074] UBI: data offset: 4096
[ 22.026580] UBI: scan info block is a empty block
[dtv_app_mtk]>[_nav_cec_ro[ 22.030858] UBI: ubi get sid err[-22]
uting_ctrl_mw_nfy_hdlr_fct][1720] MW fakes this OPCODE
[_nav_cec_routing_ctrl_mw_opcode_hdlr][1174] SAC has [ 22.047143] UBI: max. sequence number: 30625
sent <routing change>.
[dtv_app_mtk]>
[!!!R[ 22.056040] UBI: attached mtd11 to ubi2
[ 22.059451] UBI: MTD device name: "perm"
[ 22.064290] UBI: MTD device size: 5 MiB
[ 22.069319] UBI: number of good PEBs: 39
[ 22.074525] UBI: number of bad PEBs: 0
[ 22.077779] UBI: number of corrupted PEBs: 0
[ 22.083058] UBI: max. allowed volumes: 128
[ 22.087382] UBI: wear-leveling threshold: 4096
[ 22.091567] UBI: number of internal volumes: 1
[ 22.096572] UBI: number of user volumes: 1
[ 22.102056] UBI: available PEBs: 0
[ 22.104956] UBI: total number of reserved PEBs: 39
[ 22.109922] UBI: number of PEBs reserved for bad PEB handling: 5
[ 22.116146] UBI: max/mean erase counter: 1119/785
[ 22.120305] UBI: image sequence number: 313261675
[ 22.125273] UBI: background thread "ubi_bgt2d" started, PID 778
eturn fail:nav_cec_sys_info.c:_nav_cec_sys_info_mw_opcode_hdlr:585:1]
UBI device number 2, total 39 LEBs (4952064 bytes, 4.7 MiB), available 0 LEBs (0 bytes), LEB size 126976 bytes (124.0 KiB)
[ 22.161872] UBIFS: recovery needed
[ 22.231217] UBIFS: recovery completed
[ 22.232620] UBIFS: mounted UBI device 2, volume 0, name "perm"
[ 22.238672] UBIFS: file system size: 2539520 bytes (2480 KiB, 2 MiB, 20 LEBs)
[ 22.245408] UBIFS: journal size: 1142785 bytes (1116 KiB, 1 MiB, 8 LEBs)
[ 22.252939] UBIFS: media format: w4/r0 (latest is w4/r0)
[ 22.258329] UBIFS: default compressor: lzo
[ 22.262327] UBIFS: reserved for root: 0 bytes (0 KiB)
[dtv_app_mtk]>[FM-Linux]Mount /dev/mtd11 to /perm successfully.
[FM](/dev/mtd11) is mounted to (/perm) successfully(0)
# mount 3rdb DMVERITY(SquashFS read-only)
[ 22.422092] /dev/mtdblock10: NFSB header found and verified.
[ 22.428325] device-mapper: verity: dev:mtdblock10 hash:mtdblock10 [sectors:584 blocks:18229]
[ 22.434903] device-mapper: table: 254:1: adding target device (start sect 0 len 145832) caused an alignment inconsistency
[dtv_app_mtk]>[DM]status changed:device path:/block/dm-1
[DM]_dm_check_device_changed entered(changed device path:/block/dm-1)...
[DM]_dm_check_device_changed exited(changed device path:/block/dm-1)...
[DM]No dev name found.
[DM]status changed:device path:/block/dm-1
[DM]_dm_check_device_changed entered(changed device path:/block/dm-1)...
[DM]_dm_check_device_changed exited(changed device path:/block/dm-1)...
[DM]No dev name found.
[dtv_app_mtk]>real 0m 0.04s
[dtv_app_mtk]>user 0m 0.00s
[dtv_app_mtk]>sys 0m 0.00s
[FM](/dev/mtdblock10) is mounted to (/3rd) unsuccessfully(-6)
MHEG5 TPS start to setup
[MHEG5_NVM]rw root path = /3rd_rw
MHEG5 TPS setup failed to create dir(-6)
# mount 3rd_rw
[ 22.615898] UBI: attaching mtd12 to ubi4
[ 22.617082] UBI: save scan info advance: 1
[ 22.622255] UBI: physical eraseblock size: 131072 bytes (128 KiB)
[ 22.627917] UBI: logical eraseblock size: 126976 bytes
[ 22.633442] UBI: smallest flash I/O unit: 2048
[ 22.637790] UBI: VID header offset: 2048 (aligned 2048)
[ 22.646216] UBI: data offset: 4096
[ 22.657875] UBI: scan info block is a empty block
[ 22.660294] UBI: ubi get sid err[-22]
[ 23.075608] UBI: max. sequence number: 35152
[ 23.088769] UBI: attached mtd12 to ubi4
[ 23.089877] UBI: MTD device name: "3rd_rw"
[ 23.095359] UBI: MTD device size: 120 MiB
[ 23.100189] UBI: number of good PEBs: 959
[ 23.104963] UBI: number of bad PEBs: 0
[ 23.109448] UBI: number of corrupted PEBs: 0
[ 23.113700] UBI: max. allowed volumes: 128
[ 23.117868] UBI: wear-leveling threshold: 4096
[ 23.123709] UBI: number of internal volumes: 1
[ 23.127001] UBI: number of user volumes: 1
[ 23.132670] UBI: available PEBs: 0
[ 23.136490] UBI: total number of reserved PEBs: 959
[ 23.140765] UBI: number of PEBs reserved for bad PEB handling: 9
[ 23.147004] UBI: max/mean erase counter: 41/37
[ 23.151419] UBI: image sequence number: 169114786
[ 23.156320] UBI: background thread "ubi_bgt4d" started, PID 810
[dtv_app_mtk]>UBI device number 4, total 959 LEBs (121769984 bytes, 116.1 MiB), available 0 LEBs (0 bytes), LEB size 126976 bytes (124.0 KiB)
[ 23.202770] UBIFS: recovery needed
[ 23.275273] UBIFS: recovery completed
[ 23.276200] UBIFS: mounted UBI device 4, volume 0, name "3rd_rw"
[ 23.282602] UBIFS: file system size: 118722560 bytes (115940 KiB, 113 MiB, 935 LEBs)
[ 23.290420] UBIFS: journal size: 9023488 bytes (8812 KiB, 8 MiB, 72 LEBs)
[ 23.297762] UBIFS: media format: w4/r0 (latest is w4/r0)
[ 23.305327] UBIFS: default compressor: lzo
[ 23.307237] UBIFS: reserved for root: 0 bytes (0 KiB)
[dtv_app_mtk]>[FM-Linux]Mount /dev/mtd12 to /3rd_rw successfully.
[FM](/dev/mtd12) is mounted to (/3rd_rw) successfully(0)
MHEG5 TPS start to setup
[MHEG5_NVM]rw root path = /3rd_rw
[MHEG5_NVM]created mheg5 root path = /3rd_rw/mh5n
MHEG5 TPS setup OK
# mount 3rd_ro
[ 23.450256] UBI: attaching mtd13 to ubi3
[ 23.451443] UBI: save scan info advance: 1
[ 23.456961] UBI: physical eraseblock size: 131072 bytes (128 KiB)
[ 23.462352] UBI: logical eraseblock size: 126976 bytes
[ 23.467609] UBI: smallest flash I/O unit: 2048
[ 23.474079] UBI: VID header offset: 2048 (aligned 2048)
[ 23.481726] UBI: data offset: 4096
[ 23.493032] UBI: scan info block is a empty block
[ 23.495092] UBI: ubi get sid err[-22]
[ 23.582351] UBI: max. sequence number: 2
[ 23.596870] UBI: attached mtd13 to ubi3
[ 23.597929] UBI: MTD device name: "ro_data"
[ 23.609188] UBI: MTD device size: 30 MiB
[ 23.614275] UBI: number of good PEBs: 239
[ 23.618608] UBI: number of bad PEBs: 0
[ 23.622147] UBI: number of corrupted PEBs: 0
[ 23.629091] UBI: max. allowed volumes: 128
[ 23.630928] UBI: wear-leveling threshold: 4096
[ 23.637428] UBI: number of internal volumes: 1
[ 23.640489] UBI: number of user volumes: 1
[ 23.644656] UBI: available PEBs: 0
[ 23.649400] UBI: total number of reserved PEBs: 239
[ 23.654108] UBI: number of PEBs reserved for bad PEB handling: 5
[ 23.660706] UBI: max/mean erase counter: 1/0
[ 23.664070] UBI: image sequence number: 777810414
[ 23.669229] UBI: background thread "ubi_bgt3d" started, PID 827
[dtv_app_mtk]>UBI device number 3, total 239 LEBs (30347264 bytes, 28.9 MiB), available 0 LEBs (0 bytes), LEB size 126976 bytes (124.0 KiB)
[ 23.726128] UBIFS: mounted UBI device 3, volume 0, name "3rd_ro"
[ 23.729446] UBIFS: mounted read-only
[ 23.733248] UBIFS: file system size: 27934720 bytes (27280 KiB, 26 MiB, 220 LEBs)
[ 23.743330] UBIFS: journal size: 4063232 bytes (3968 KiB, 3 MiB, 32 LEBs)
[ 23.747886] UBIFS: media format: w4/r0 (latest is w4/r0)
[ 23.754713] UBIFS: default compressor: lzo
[ 23.757780] UBIFS: reserved for root: 0 bytes (0 KiB)
[dtv_app_mtk]>[FM-Linux]Mount /dev/mtd13 to /3rd_ro successfully.
[FM](/dev/mtd13) is mounted to (/3rd_ro) successfully(0)
reason: 0x00000006 - 0x00000000
[dtv_app_mtk]>
[dtv_app_mtk]>_nav_cec_misc_icl_nfy_func.
_nav_cec_misc_3rd_chg_hdlr.
t_change_info.s_org_app_id is dtv_app_mtk, org app status 1 ,focus app id dtv_app_mtk.
[_nav_cec_misc_3rd_chg_hdlr][352] display ui 0.
[_nav_cec_misc_3rd_chg_hdlr][368] ui 0.
[ ACFG_CUST]: t_change_info:
[dtv_app_mtk]> s_org_app_id:dtv_app_mtk
[dtv_app_mtk]> ui1_org_app_status:1
[dtv_app_mtk]> s_focus_app_id:dtv_app_mtk
_input_cec_nfy_handler()
ui1_num: 0tk]>
ui1_num: 0tk]>
[ 24.245123] rtusb init rtusbSTA --->
[ 24.246777]
[ 24.246781]
[ 24.246784] === pAd = e05e6000, size = 1053344 ===
[ 24.246788]
[ 24.256014] <-- RTMPAllocAdapterBlock, Status=0
[ 24.259889] Efuse Size=0x2d [2d0-2fc]
[ 24.263550] NVM is EFUSE
[ 24.266827] usbcore: registered new interface driver rtusbSTA
[ 24.534612] NTFS driver 2.1.30 [Flags: R/O MODULE].
[ 24.573559] usbcore: registered new interface driver usbhid
[ 24.576709] usbhid: USB HID core driver
[dtv_app_mtk]>mount: mounting none on /proc/bus/usb failed: Device or resource busy
[INET] 18.915, ni_mon_thread.1861 >>> ra0 is plug!
[ 24.625791] v4l2_common: Unknown symbol v4l2_ctrl_get_menu (err 0)
[ 24.629700] v4l2_common: Unknown symbol v4l2_ctrl_fill (err 0)
[dtv_app_mtk]>insmod: can't insert '/basic/modules/v4l2-common.ko': unknown symbol in module or invalid parameter
[ 24.670347] Linux video capture interface: v2.00
[ 24.686672] usbcore: registered new interface driver uvcvideo
[ 24.690502] USB Video Class driver (v1.1.0)
[ 24.704150] !@#!@# @@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@ alsa_card_mtk_init 201202101600
_input_cec_nfy_handler()
ui1_num: 0tk]>
ui1_num: 0tk]>
[_nav_cec_sys_app_mw_msg_hdlr] [1096]:Export Activities.
[_nav_cec_sys_app_export_activities][405]Active source la 1.
[_nav_cec_sys_app_export_activities][405]Active source la 2.
[_nav_cec_sys_app_export_activities][405]Active source la 3.
[_nav_cec_sys_app_export_activities][405]Active source la 4.
[_nav_cec_sys_app_export_activities][405]Active source la 5.
[ 25.394296] ===============
[ 25.394301] DVBT2_TunerSetAttribute
[ 25.394305] , e_set_type = 283
[ 25.428926] [PCMCIA]PATCH_FOR_NEOTION_MACRO_BLOCK patch enable, demod TS disable
[ 25.433552] ===============
[ 25.433557] DVBT2_TunerSetAttribute
[ 25.433561] , e_set_type = 283
[_nav_cec_sys_app_export_activities][405]Active source la 6.
[ 25.473307] [PCMCIA]PATCH_FOR_NEOTION_MACRO_BLOCK patch enable, demod TS enable
[_nav_cec_sys_app_export_activities][405]Active source la 7.
[_nav_cec_sys_app_export_activities][405]Active source la 8.
[_nav_cec_sys_app_export_activities][405]Active source la 9.
**********DirectFBInit()
[dtv_app_mtk]>gl_dfb_plane_open want plane 1
[dtv_app_mtk]>gl_dfb_plane_open want plane 1
[dtv_app_mtk]>gl_dfb_plane_enum want plane 0
[dtv_app_mtk]>[NETTV][M]>>>>>>>>>>[TvControl.cpp][559], setLanguage() : Invoke IMnettvP_UserChangedLanguage, 4
[dtv_app_mtk]>gl_dfb_plane_open want plane 0
[dtv_app_mtk]>gl_dfb_plane_open want plane 2
[dtv_app_mtk]>gl_dfb_plane_open want plane 1
[dtv_app_mtk]>gl_dfb_plane_open want plane 1
[dtv_app_mtk]>[NETTV][M]>>>>>>>>>>[TvControl.cpp][724], setCountry() : Invoke IMnettvP_UserChangedCountry, RU
[dtv_app_mtk]>[ipepgmw_epgctl_set_day_time_saving:606]>
[dtv_app_mtk]>[606:IMnettvP_UserChangedLanguage]> [P]========>>User Language=en
[dtv_app_mtk]>[729:IMnettvP_UserChangedCountry]> [P]========>> change to country: RU
[dtv_app_mtk]>[ipepgmw_epgctl_set_time_zone:611]>
[dtv_app_mtk]>[1343:IMnettvP_Ipepg_SetDayTimeSaving]> [P]========>>DayTimeSaving = 0
[dtv_app_mtk]>[694:nettvapp_SetDayTimeSaving]> DayTimeSaving =0
[dtv_app_mtk]>
[dtv_app_mtk]>[NETTV][M]>>>>>>>>>>[TvControl.cpp][807], setConnectionType() : Invoke IMnettvP_Ipepg_SetConnectionType ui1_type = 5, ui2_svl_id=1
[dtv_app_mtk]>[ipepgmw_epgctl_set_connection_type:625]>
[dtv_app_mtk]>[1349:IMnettvP_Ipepg_SetTimeZone]> [P]========>>TimeZone = 10800
[dtv_app_mtk]>[709:nettvapp_SetTimeZone]> TimeZone =10800
[dtv_app_mtk]>
[dtv_app_mtk]>[NETTV][M]>>>>>>>>>>[TvControl.cpp][883], setTimeSaving() Invoke IMnettvP_Ipepg_SetDayTimeSaving 0
[dtv_app_mtk]>[ipepgmw_epgctl_set_day_time_saving:606]>
[dtv_app_mtk]>[1361:IMnettvP_Ipepg_SetConnectionType]> [P]========>>Connection Type =
[dtv_app_mtk]>[743:nettvapp_SetConnectionType]> type =
[dtv_app_mtk]>
[dtv_app_mtk]>[NETTV][M]>>>>>>>>>>[TvControl.cpp][897], setRegion() : Invoke IMnettvP_Ipepg_SetRegion, 1
[dtv_app_mtk]>[ipepgmw_epgctl_set_region:616]>
[dtv_app_mtk]>[1343:IMnettvP_Ipepg_SetDayTimeSaving]> [P]========>>DayTimeSaving = 0
[dtv_app_mtk]>[694:nettvapp_SetDayTimeSaving]> DayTimeSaving =0
[dtv_app_mtk]>
[dtv_app_mtk]>[ipepgmw_epgctl_set_region_to_shmemory:1288]>
[dtv_app_mtk]>[1355:IMnettvP_Ipepg_SetRegion]> [P]========>>Region = 1
[dtv_app_mtk]>[726:nettvapp_SetRegion]> region =1
[dtv_app_mtk]>
[dtv_app_mtk]>[1613:IMnettvP_DB_InformBcNetworkOperator]> [P]========>>
[dtv_app_mtk]>[205:_imnettv_copydata]> [P]========>>copy data files from /usr/opera/opera_home to /tmp/opera_home success
[dtv_app_mtk]>mkdir: cannot create directory '/tmp/opera_home': File exists
[dtv_app_mtk]>cp: omitting directory '/usr/opera/opera_home/handlers'
[dtv_app_mtk]>[_nav_cec_sys_app_export_activities][405]Active source la 10.
[dtv_app_mtk]>cp: omitting directory '/usr/opera/opera_home/plugins'
[208:_imnettv_copydata]> [P]========>>copy opera data files from /mnt/broser to /tmp/opera_home success
[dtv_app_mtk]>[212:_imnettv_copydata]> [P]========>>copy opera pem files from /mnt/broser to /tmp/ success
[dtv_app_mtk]>[_nav_cec_sys_app_export_activities][405]Active source la 11.
[dialserver]>
[ 28.541259] pgd = dd0b0000
[ 28.541292] [987a0000] *pgd=1b789831, *pte=00000000, *ppte=00000000
[ 28.547444]
[ 28.548999] Pid: 763, comm: nettv
[ 28.553870] CPU: 0 Tainted: P (3.0.13 #1)
[ 28.558879] PC is at 0x4409c2c0
[ 28.561951] LR is at 0x40cd3b98
[ 28.565120] pc : [<4409c2c0>] lr : [<40cd3b98>] psr: 20000010
[ 28.565126] sp : 52045aa0 ip : 00000000 fp : 52045c04
[ 28.576824] r10: 00000401 r9 : 1b0f1dc0 r8 : a2649ccb
[ 28.581784] r7 : 00000000 r6 : 40c06b7c r5 : 1b0f21f1 r4 : 0162c878
[ 28.588320] r3 : 987a0000 r2 : 04cfa1e9 r1 : 00000000 r0 : 823a8000
[ 28.595087] Flags: nzCv IRQs on FIQs on Mode USER_32 ISA ARM Segment user
[ 28.601999] Control: 10c53c7d Table: 1d0b0059 DAC: 00000015
window size: 1
window 0: [0x2022e800], 0 type :0
[AppManager:removeFocusProc]no more proc[ 28.716692] Restarting system.
Boot-
DRAM Channel A Calibration.
---и повторяется---