Витася писал(а): подключи динамики, это от того что они отключены. либо проблема с унч, его питанием ,обвязкой
Подключил динамики, отпаял резистор 3U77, ошибка такая же. На линии SUPPLY-FAULT кратковременно низкий уровень, сразу перед выключением. В точке IU12 кратковременно 6 вольт так же перед отключением. Иногда вместо 9 раз, мигает 6, мне кажется что там во время загрузки, какой то стабилизатор по току выключается, так как телек вырубает бп только секунд через 10, проц успевает нагреться немного. ---------- Добавлено спустя 1 час 58 минут 50 секунд: ---------- Точку SDM запаял, теперь так же точно вырубает бп, но не показывает код(просто светит светодиот дежурки и гаснет). Куда терминал подключать? ---------- Добавлено спустя 6 минут 37 секунд: ---------- Всё, увидел. ---------- Добавлено спустя 12 минут 17 секунд: ----------
лог загрузки
uBTM NDK R5.2b retail Feb 7 2007 11:56:37 Boot device - ST NAND512W3A BootFFS initialization - OK uBTM has been enabled with ECC Searching BootLoader.tdf File System ID is BFFS_ID Loading /bffs0/BootLoader.tdf-Done
Starting /bffs0/BootLoader.tdf JBL enabled with ECC check
Initialize I2C module
BootLoader OS_R0.4.6 retail Apr 25 2007 12:01:32 Searching boot.bat Executing /bffs2/boot.bat from label "1:" * SR1->Coldboot * On error goto 60 * Loading /bffs2/atvTm0App.tdf - ok * Loading /bffs2/tm5050.tdf - ok * Loading /bffs2/Kernel.tdf - ok * MemFill 0x83fff000 0x1000 0xff * Signal 30 Parsing Kernel Boot Command Line
CMD_LINE arguments passed by JBL : * Starting /bffs2/Kernel.tdf(Warning) [-29976] MDCS write timeout 0/0 from 2 to 6 at 1be47064; EPC 801d18ac "mtv522EU/22M startup script ..." "Mounting file systems" Total usertime mount for /proc: 0,000000 [Sec] Total systemtime mount for /proc: 0,000000 [Sec] Total usertime mount for /sys: 0,000000 [Sec] Total systemtime mount for /sys: 0,010000 [Sec] Total usertime mount for /dev/shm: 0,000000 [Sec] Total systemtime mount for /dev/shm: 0,000000 [Sec] Total usertime mount for /dev/pts: 0,000000 [Sec] Total systemtime mount for /dev/pts: 0,000000 [Sec] "Mounting the flash file systems" "Launching TV application" checking hotboot: NO Total usertime mount for /mnt/jffs0: 0,000000 [Sec] Total systemtime mount for /mnt/jffs0: 0,260000 [Sec] Incompatible standby version found (18.x.1.18). Expected 18.x.1.19.
Total usertime mount for /mnt/jffs1: 0,000000 [Sec] Total systemtime mount for /mnt/jffs1: 0,790000 [Sec] start_Init clearing m_InitDoneBlunk mounted: </dev/mtdblSlave /dev/pts/0 RW partition: 4 mounting partition 4 to jffs2 file system failed
MountJffsPartition( 4, TRUE ) failed, mountcheck will try again RW partition: 5 mounting partition 5 to jffs2 file system failed
MountJffsPartition( 5, TRUE ) failed, mountcheck will try again mlock patch inited
/mnt/jffs0/rupg/cetv/display found - Layoutcheck OK Display flash file : Layout version = 5 ; Content version = 56 Display flash file : Project Id = 0 ; Branch Id = 64 version string: DISPT_000.064.005.056 Using screen option 131, name LCD AUO V4 42"Diversity: BoardType=/82, BoardVe rsion=3, Detected pnx8535 version=M2 AmbientLightGenerator : None AmbientLightMode : None AmbientLightTechnology : None CabinetNumber : 11 ChannelDecoderType : Tda10048 ChannelDecoder2Type : None ClearLcdSupported : True DimmingBacklightSupported : True DisplayRawNumber : 131 DvbHdSupported : False EpldPresent : False HDMIMuxPresent : Mux4 IfDemVersion : V2 LightSensor : Present LightSensorType : MS7 Sti7100Present : False PacificPresent : False Region : Europe Pnx5050Present : False SawVersion : New IF Mode (DVB-C) : Low IF TunerI2cConfig : ViaI2cMux TunerType : 24
RU Flash file not found in /mnt/jffs0/rupg/tv520avi/cabinet11 RO Flash file not found in /mnt/jffs0/ro/tv520avi/cabinet11 Local flash file not found in file/cabinet11 RU Flash file found in /mnt/jffs0/rupg/tv520avi/cabinet Cabinet flash file : Layout version = 4 ; Content version = 28 Cabinet flash file : Project Id = 0 ; Branch Id = 64 version string: ACSTS_000.064.004.028 Using cabinet option 11, name ME8_42Entry /mnt/jffs0/rupg/cetv/profileset1.pqs found File: profileset1.pqs, version: 2.5, id: version_5
/mnt/jffs0/rupg/cetv/usersettings1.pqu found File: usersettings1.pqu, version: 0.2, id: version_5
/mnt/jffs0/rupg/cetv/fixedsettings1.pqf found File: fixedsettings1.pqf, version: 0.4, id: version_5
/mnt/jffs0/rupg/cetv/lightsensor1.pql found File: lightsensor1.pql, version: 0.1, id: CEHTV: LED Behaviour power chgd notifyed (from=1,to=5) startr_init Startup m_InitDoneBlunk: 1, m_InitDoneMain: 1 Main software: Q522E_0.64.30.5 Standby software: STDBY_18.12.1.18 CEHTV: LED Behaviour main LED=1,SBY LED =0. enable LVDS
svbas pgselN_OnProgramChangeRequested CEHTV: RC_LED = -1 (MAIN=1,SBY=0,NO=-1) CEHTV: RC_LED = -1 (MAIN=1,SBY=0,NO=-1)
svbas pgselN_OnProgramChangeCompleted
svbas pgselN_OnProgramChangeRequested (Warning) [-29037] MDCS read timeout 1/1 from 0 to 25 at 2a002000; EPC c010f2c0
svbas pgselN_OnProgramNotFound ÿ
uBTM NDK R5.2b retail Feb 7 2007 11:56:37 Boot device - ST NAND512W3A BootFFS initialization - OK uBTM has been enabled with ECC Searching BootLoader.tdf File System ID is BFFS_ID Loading /bffs0/BootLoader.tdf-Done
Starting /bffs0/BootLoader.tdf JBL enabled with ECC check
Initialize I2C module
BootLoader OS_R0.4.6 retail Apr 25 2007 12:01:32 Searching boot.bat Executing /bffs2/boot.bat from label "1:" * SR1->Coldboot * On error goto 60 * Loading /bffs2/atvTm0App.tdf - ok * Loading /bffs2/tm5050.tdf - ok * Loading /bffs2/Kernel.tdf - ok * MemFill 0x83fff000 0x1000 0xff * Signal 30 Parsing Kernel Boot Command Line
CMD_LINE arguments passed by JBL : * Starting /bffs2/Kernel.tdf(Warning) [-29976] MDCS write timeout 0/0 from 2 to 6 at 1be47064; EPC 801d18ac "mtv522EU/22M startup script ..." "Mounting file systems" Total usertime mount for /proc: 0,000000 [Sec] Total systemtime mount for /proc: 0,000000 [Sec] Total usertime mount for /sys: 0,000000 [Sec] Total systemtime mount for /sys: 0,010000 [Sec] Total usertime mount for /dev/shm: 0,000000 [Sec] Total systemtime mount for /dev/shm: 0,000000 [Sec] Total usertime mount for /dev/pts: 0,000000 [Sec] Total systemtime mount for /dev/pts: 0,000000 [Sec] "Mounting the flash file systems" "Launching TV application" checking hotboot: NO Total usertime mount for /mnt/jffs0: 0,000000 [Sec] Total systemtime mount for /mnt/jffs0: 0,230000 [Sec] Incompatible standby version found (18.x.1.18). Expected 18.x.1.19.
Total usertime mount for /mnt/jffs1: 0,000000 [Sec] Total systemtime mount for /mnt/jffs1: 0,780000 [Sec] start_Init clearing m_InitDoneBlunk mounted: </dev/mtdblSlave /dev/pts/0 RW partition: 4 mounting partition 4 to jffs2 file system failed
MountJffsPartition( 4, TRUE ) failed, mountcheck will try again RW partition: 5 mounting partition 5 to jffs2 file system failed
MountJffsPartition( 5, TRUE ) failed, mountcheck will try again mlock patch inited
/mnt/jffs0/rupg/cetv/display found - Layoutcheck OK Display flash file : Layout version = 5 ; Content version = 56 Display flash file : Project Id = 0 ; Branch Id = 64 version string: DISPT_000.064.005.056 Using screen option 131, name LCD AUO V4 42"Diversity: BoardType=/82, BoardVe rsion=3, Detected pnx8535 version=M2 AmbientLightGenerator : None AmbientLightMode : None AmbientLightTechnology : None CabinetNumber : 11 ChannelDecoderType : Tda10048 ChannelDecoder2Type : None ClearLcdSupported : True DimmingBacklightSupported : True DisplayRawNumber : 131 DvbHdSupported : False EpldPresent : False HDMIMuxPresent : Mux4 IfDemVersion : V2 LightSensor : Present LightSensorType : MS7 Sti7100Present : False PacificPresent : False Region : Europe Pnx5050Present : False SawVersion : New IF Mode (DVB-C) : Low IF TunerI2cConfig : ViaI2cMux TunerType : 24
RU Flash file not found in /mnt/jffs0/rupg/tv520avi/cabinet11 RO Flash file not found in /mnt/jffs0/ro/tv520avi/cabinet11 Local flash file not found in file/cabinet11 RU Flash file found in /mnt/jffs0/rupg/tv520avi/cabinet Cabinet flash file : Layout version = 4 ; Content version = 28 Cabinet flash file : Project Id = 0 ; Branch Id = 64 version string: ACSTS_000.064.004.028 Using cabinet option 11, name ME8_42Entry /mnt/jffs0/rupg/cetv/profileset1.pqs found File: profileset1.pqs, version: 2.5, id: version_5
/mnt/jffs0/rupg/cetv/usersettings1.pqu found File: usersettings1.pqu, version: 0.2, id: version_5
/mnt/jffs0/rupg/cetv/fixedsettings1.pqf found File: fixedsettings1.pqf, version: 0.4, id: version_5
/mnt/jffs0/rupg/cetv/lightsensor1.pql found File: lightsensor1.pql, version: 0.1, id: CEHTV: LED Behaviour power chgd notifyed (from=1,to=5) startr_init Startup m_InitDoneBlunk: 1, m_InitDoneMain: 1 Main software: Q522E_0.64.30.5 Standby software: STDBY_18.12.1.18 CEHTV: LED Behaviour main LED=1,SBY LED =0. enable LVDS
svbas pgselN_OnProgramChangeRequested CEHTV: RC_LED = -1 (MAIN=1,SBY=0,NO=-1) CEHTV: RC_LED = -1 (MAIN=1,SBY=0,NO=-1)
svbas pgselN_OnProgramChangeCompleted
svbas pgselN_OnProgramChangeRequested (Warning) [-29023] MDCS read timeout 1/1 from 0 to 25 at 2a002000; EPC c010f2c0
svbas pgselN_OnProgramNotFound
|