Ремонт: Ноутбуков, Компьютеров https://vlab.su/ |
|
Goclever 70W https://vlab.su/viewtopic.php?f=254&t=21838 |
Страница 1 из 1 |
Bahmut [ 30 май 2014, 13:30 ] | |
Заголовок сообщения: | Goclever 70W |
Привет всем, пытаюсь починить планшет. Перестал включаться, при нажатии на кнопку вкл. ничего не происходит, начинает греться проц. Подключил к ЛБП - потребление тока постоянное 300 мА, после нажатия на кнопку включения. Пытался посмотреть через UART, что же происходит, жив ли загрузчик. Пользуюсь KiTTY, в окне терминала одни кракозябры, кодировки менял - ничего не помогает. Шнурок для UART достался от кассового аппарата собран на ST232 и CP2102, дрова ставил последние. Может кто в курсе, как бороться с такой бедой. |
BaserLexx [ 30 май 2014, 22:53 ] | |
Заголовок сообщения: | Re: Goclever 70W |
У коллег смотрели? |
Bahmut [ 31 май 2014, 13:08 ] | |
Заголовок сообщения: | Re: Goclever 70W |
BaserLexx писал(а): У коллег смотрели? Да, как раз статьёй, найденной на этом сайте, и руководствовался. Пробовал на разных компах, никаких изменений, прийдётся, наверное, самому переходник ваять(((. |
Bahmut [ 22 июл 2014, 16:39 ] | |
Заголовок сообщения: | Re: Goclever 70W |
Не удалось, ф топку. |
kaliyan [ 22 июл 2014, 21:54 ] | |
Заголовок сообщения: | Re: Goclever 70W |
Bahmut писал(а): потребление тока постоянное 300 мА, после нажатия на кнопку включения Bahmut писал(а): начинает греться проц Проц под замену - то есть аппарат ф топку! ---------- Добавлено спустя 1 минуту 58 секунд: ---------- Проц хиленький, а ускоглазые не предкусмотрели ESD защиту, по этому он мрёт как "бот перед гопником" )))) |
Bahmut [ 06 окт 2014, 22:47 ] | |
Заголовок сообщения: | Re: Goclever 70W |
Оживлю тему, вернулся опять к этому планшету, появился нормальный UART-USB переходник. В консоли выдаёт вот такую котавасию: spl: start bnd busw: 8 i: randomizer (224) got id: ad d7 94 91 60 44 ad d7 id3 do not match, 91<=>9a got id: ad d7 94 91 60 44 ad d7 id3 do not match, 91<=>da got id: ad d7 94 91 60 44 ad d7 nand configuratino matched. NAND config got: IF: 0 Randomizer: 1 Cycle: 5 MECC level: 6 SECC level: 1 ECC enable: 1 Bad0: 0 Bad1: ff Sysinfo: 10 Pagesize: 2000 Sparesize: 280 Blocksize: 200000 Timing: 18323 phyread: 4023 phydelay: 3818 busw: 8 i: randomizer (576) spl: seed[0] = 0x1c723550 spl: seed[1] = 0x20fe074e spl: seed[2] = 0x1698347e spl: seed[3] = 0xffffec80 spl: H27UBG8T2CTR start 0x100800000, 0x80400 spl: crc_ori = 0x72110fbb match crc_calc = 0x72110fbb spl: auto: 1 (1) spl: auto: 2 (2) ecc unfixed: 1.0 spl: auto: 3 (3) i: type (1) i: signature (0) ecc unfixed: 1.0 spl: auto: 4 (4) spl: jump U-Boot 2009.08-dirty ( 7? 27 2013 - 17:14:21) Shanghai InfoTM Microelectronics Co., Ltd. Memory type: DDRII 256 MB Using default environment Console devices(i/o/e): serial, serial, serial i: randomizer (224) ======cfg->max_seed_cycle is 0 got id: ad d7 94 91 60 44 ad d7 id3 do not match, 91<=>9a got id: ad d7 94 91 60 44 ad d7 id3 do not match, 91<=>da got id: ad d7 94 91 60 44 ad d7 nand configuratino matched. NAND config got: IF: 0 Randomizer: 1 Cycle: 5 MECC level: 6 SECC level: 1 ECC enable: 1 Bad0: 0 Bad1: ff Sysinfo: 10 Pagesize: 2000 Sparesize: 280 Blocksize: 200000 Timing: 18323 busw: 8 i: randomizer (576) ======cfg->max_seed_cycle is 256 H27UBG8T2CTR get param from uboot0 default param 0x32, 0x3b, 0x58, 0xa4, 0x36, 0x3e, 0x4c, 0x92 1st param 0x3c, 0x36, 0x5c, 0xa0, 0x40, 0x39, 0x50, 0x8e 2nd param 0x3a, 0x39, 0x55, 0x99, 0x3e, 0x3c, 0x49, 0x87 3th param 0x38, 0x38, 0x52, 0x9b, 0x3c, 0x3b, 0x46, 0x89 4th param 0x34, 0x36, 0x4f, 0x98, 0x38, 0x39, 0x43, 0x86 5th param 0x2d, 0x34, 0x4b, 0x94, 0x31, 0x37, 0x3f, 0x82 6th param 0x23, 0x32, 0x47, 0x91, 0x27, 0x35, 0x3b, 0x7f 7th param 0x19, 0x25, 0x3b, 0x81, 0x1d, 0x28, 0x2f, 0x6f cfg: 0x3c000000 read items: id=1 nnd length forced to: 0x4000 begin init. default serial:iMAPb1c2a1a3 default serial:iMAPb1c2a1a3 keys.fastboot not exist read ius header addr=8e4050f0, loc=1000000, size=200, j=0 header check passed. IUS found in device 7 erase nand 48M -- 4G Assign OK. Erase done. 12 images found in package. processing image: 0, type=0 skipped: image is masked as 0 processing image: 1, type=3 skipped: image is masked as 0 processing image: 2, type=4 skipped: image is masked as 0 processing image: 3, type=4 skipped: image is masked as 0 processing image: 4, type=49 skipped: image is masked as 0 processing image: 5, type=4 max=1000000, bs=4000 9M remains 8M remains 7M remains 6M remains 5M remains 4M remains 3M remains 2M remains 1M remains 0M remains processing image: 6, type=4 max=800000, bs=4000 5M remains 4M remains 3M remains 2M remains 1M remains 0M remains processing image: 7, type=50 IUS boot recovery. cfg: 0x3c000000 read items: id=1 nnd length forced to: 0x4000 begin init. part--- bootre--- bootre1--- fetch logo@0x3000000 ... nnd length forced to: 0x400000 offset = 0x3000000, read rerty level 5 auto: 5 (5) offset = 0x3000000, read rerty level 6 auto: 6 (6) offset = 0x3000000, read rerty level 7 auto: 7 (7) offset = 0x3000000, read rerty level 0 auto: 0 (0) offset = 0x3000000, read rerty level 1 auto: 1 (1) offset = 0x3000000, read rerty level 2 auto: 2 (2) offset = 0x3000000, read rerty level 3 auto: 3 (3) read retry failed offset = 0x3000000, read rerty level 4 auto: 4 (4) === uboot1_vaild === start 2000000 size 800000 nnd length forced to: 0x2000 length 40000 nnd length forced to: 0x40000 nnd length forced to: 0x2000 length 40000 nnd length forced to: 0x40000 all uboot1 good fetch recovery-rd@0x9000000 ... nnd length forced to: 0x2000 offset = 0x9000000, read rerty level 5 auto: 5 (5) offset = 0x9000000, read rerty level 6 auto: 6 (6) offset = 0x9000000, read rerty level 7 auto: 7 (7) offset = 0x9000000, read rerty level 0 auto: 0 (0) offset = 0x9000000, read rerty level 1 auto: 1 (1) offset = 0x9000000, read rerty level 2 auto: 2 (2) offset = 0x9000000, read rerty level 3 auto: 3 (3) read retry failed offset = 0x9000000, read rerty level 4 auto: 4 (4) read header failed 0xffffffff Erro: Failed to load recovery-rd from gaven disk, system halted Я так понимаю, что проблема скрыта в самом образе прошивки, может, кто в курсе, как это побороть. Гугл переводчик выдаёт так :"Не удалось загрузить восстановления-сподь от Gaven диск, система остановила". |
Dimon_k [ 28 окт 2014, 12:54 ] | |
Заголовок сообщения: | Re: Goclever 70W |
Шить через IUW |
romeo [ 30 янв 2015, 12:48 ] | |
Заголовок сообщения: | Re: Goclever 70W |
Всем привет. Подниму тему, так как у меня та же проблема. Лог в Kitty останавливается на Erro: Failed to load recovery-rd from gaven disk, system halted Bahmut, как решили проблему? Я так понимаю, файл recovery-rd.img битый?
Вот лог:
Шил флешку через IUW |
Страница 1 из 1 | Часовой пояс: UTC + 4 часа |
Powered by phpBB © 2000, 2002, 2005, 2007 phpBB Group http://www.phpbb.com/ |