Ремонт: Ноутбуков, Компьютеров
https://vlab.su/

1080ти помогите пожалуйста измерить кварц
https://vlab.su/viewtopic.php?f=48&t=118368
Страница 1 из 1

hashwood [ 24 авг 2021, 14:13 ]
Заголовок сообщения:  1080ти помогите пожалуйста измерить кварц

привет, помогите пожалуйста измерить кварц.

1080 TI Blower, не определяется.
Дорожки PCI в порядке, проверил в стояке. Графический процессор нагревается, но уже через 1-2 минуты.

напряжения в норме.
1,823 В 463/480 Ом
1.034 В 60/95 Ом
1,389 В 39/65 Ом
0,827 В 0,084 Ом / 0,095 Ом

GPU мертв? Стоит ли реболить, если линии PCI в порядке?
вот видео с кварцем:

https://youtu.be/770PtbbqhKc
https://youtu.be/AbKanZ7yb1A

Pandemonium6 [ 24 авг 2021, 19:12 ]
Заголовок сообщения:  Re: 1080ти помогите пожалуйста измерить кварц

Did you check reference clock and the pex rail pins? Checking lanes is not enough.

hashwood [ 24 авг 2021, 20:17 ]
Заголовок сообщения:  Re: 1080ти помогите пожалуйста измерить кварц

I checked reference clock. pex rail pins ?

Posted after 40 minutes 22 seconds:
well, pex rst is 6 ohm, I don't think is ok. I will check

Pandemonium6 [ 24 авг 2021, 21:05 ]
Заголовок сообщения:  Re: 1080ти помогите пожалуйста измерить кварц

In diode mode, measure the voltage drop, not the resistance. And both reference clock signals on the bottom REFCLK+ and -. Pex reset diode voltage drop with red to the ground and black to the pex reset.

hashwood [ 24 авг 2021, 21:27 ]
Заголовок сообщения:  Re: 1080ти помогите пожалуйста измерить кварц

pex reset is not ok, measures 0.010v is shorted
Posted after 52 seconds:
A11 PEX_RST

Posted after 16 minutes 20 seconds:
can it go directly into GPU? :(

Pandemonium6 [ 24 авг 2021, 21:54 ]
Заголовок сообщения:  Re: 1080ти помогите пожалуйста измерить кварц

It can go directly or is buffered.
Take a picture of both sides. If it goes directly it is the game over. And are you sure you measure the right pin? In all my fauly cards all pex resets are open, infinity or almost infinity and they are not buffered. So it is strange that you have a short there. Take a close picture and mark what and how you measure?

hashwood [ 24 авг 2021, 22:09 ]
Заголовок сообщения:  Re: 1080ти помогите пожалуйста измерить кварц

i guess in this case it goes directly. :(
there is another 1070 asus that goes directly, at least it has space for logic on pcb, but not populated.

Posted after 16 minutes 59 seconds:
I measure PEX RESET for sure, pin A11 (from other boardvirews). negative on ground positive on pex reset.

Pandemonium6 [ 24 авг 2021, 22:33 ]
Заголовок сообщения:  Re: 1080ти помогите пожалуйста измерить кварц

Lane0 output is on the other side without capacitors.
PEX_RESET looks unbuffered. Do you know why it happens? Inserting a card when the power supply is turned on even on standby without unplugging from power or riser inserted under load or riser in opposite direction in x16 slot.
If it is shorted it is rather a game over.
There is a 0.01% chance that it is a dirt or something, liquid metal but rather highly unlikely. It can be a whisker from the unleaded tin.
Use a lot of IPA and a compressed air and blow under the GPU. Maybe a reflow will help if there is a a whisker. Do not do it in a stupid way by the oven. You must reflow the balls under the GPU.

hashwood [ 24 авг 2021, 23:16 ]
Заголовок сообщения:  Re: 1080ти помогите пожалуйста измерить кварц  [РЕШЕНО]

I will try reflow. thanks
Posted after 2 minutes 25 seconds:
but normally balls gets unconnected, not shorted.

Posted after 1 minute 51 second:
first card with these kind of problems

Страница 1 из 1 Часовой пояс: UTC + 4 часа
Powered by phpBB © 2000, 2002, 2005, 2007 phpBB Group
http://www.phpbb.com/