Ремонт: Ноутбуков, Компьютеров
https://vlab.su/

NM-C511 (Ideapad S145-15API 81UT) Wrong EC ID when try to connect trough keyboard connector
https://vlab.su/viewtopic.php?f=58&t=149705
Страница 1 из 1

questore [ 26 июн 2025, 20:22 ]
Заголовок сообщения:  NM-C511 (Ideapad S145-15API 81UT) Wrong EC ID when try to connect trough keyboard connector

Hello Everyone.

I'm new about the EC programming only done it a few times, but now I have this Lenovo on my desk that responds "Wrong EC ID" code is "FFFF Rev FF" or "00FF rev FF" when trying to connect with Vertyanov v3.2
Others suggested that I change the SIO and I replaced it with a NON programmed empty chip (according to others Lenovo makes self programming SIO-s)
I have 3.3v and 5V when plugged in. but still "Wrong EC ID"
I have seen this in other Lenovo-s but never know what is the issue behind this.
Can anyone explain me why this happens?

andr-sam.f [ 27 июн 2025, 06:55 ]
Заголовок сообщения:  Re: NM-C511 (Ideapad S145-15API 81UT) Wrong EC ID when try to connect trough keyboard connector

Попробуйте прошить через i2c. Хотя эта плата прекрасно шьется и через разъем KBC. Уверены, что все питания мультиконтроллера имеются?

questore [ 27 июн 2025, 10:02 ]
Заголовок сообщения:  Re: NM-C511 (Ideapad S145-15API 81UT) Wrong EC ID when try to connect trough keyboard connector

andr-sam.f писал(а):
Try flashing via i2c. Although this board is perfectly flashable via the KBC connector. Are you sure that all the multicontroller power supplies are present?

Please specify so i can check what voltages rails need to be present on this board exactly.

andr-sam.f [ 27 июн 2025, 10:26 ]
Заголовок сообщения:  Re: NM-C511 (Ideapad S145-15API 81UT) Wrong EC ID when try to connect trough keyboard connector

Попробуйте нажать на кнопку включения при подключении к EC.
Скорее всего нет +3VS

questore [ 27 июн 2025, 11:57 ]
Заголовок сообщения:  Re: NM-C511 (Ideapad S145-15API 81UT) Wrong EC ID when try to connect trough keyboard connector

andr-sam.f писал(а):
Попробуйте нажать на кнопку включения при подключении к EC.
Скорее всего нет +3VS

You are right, SUSP# / 3VS_EN is not risen so no +3VS.
Since i have just repaced the EC, could it be faulty? Should i try programming with i2c??

andr-sam.f [ 27 июн 2025, 13:59 ]
Заголовок сообщения:  Re: NM-C511 (Ideapad S145-15API 81UT) Wrong EC ID when try to connect trough keyboard connector

У вас нет реакции на кнопку включения?
Можете попробовать запитать +3VS с лабораторного блока питания

questore [ 27 июн 2025, 14:15 ]
Заголовок сообщения:  Re: NM-C511 (Ideapad S145-15API 81UT) Wrong EC ID when try to connect trough keyboard connector

andr-sam.f писал(а):
You have no reaction to the power button?
You can try to power +3VS from a laboratory power supply


Power button is on the same connector that im using for vertyanov programming.
If i short the power_on//off pin then led is turning on on the side but 3VS has only 330mA.

Applying 3V on +3VS with LAB PSU not changed anything :(
I also have 3VALW and 5VALW

andr-sam.f [ 27 июн 2025, 21:43 ]
Заголовок сообщения:  Re: NM-C511 (Ideapad S145-15API 81UT) Wrong EC ID when try to connect trough keyboard connector

В какой момент вы нажимаете на кнопку включения или подаете +3VS?
Нужно выставить все настройки на программаторе, нажать check connection и после этого уже замкнуть pwrbtn и gnd

questore [ 28 июн 2025, 17:08 ]
Заголовок сообщения:  Re: NM-C511 (Ideapad S145-15API 81UT) Wrong EC ID when try to connect trough keyboard connector  [РЕШЕНО]

andr-sam.f писал(а):
At what point do you press the power button or apply +3VS?
You need to set all the settings on the programmer, press check connection and then close pwrbtn and gnd

It seems that 3VS was not needed for programming the EC, the program was that no matter what the schematic and board pin numbering says I had to use B-sided option and the EC responded instantly.
Now that EC is reporgrammed, I instantly have 3VS thank you for your helps.

Страница 1 из 1 Часовой пояс: UTC + 3 часа
Powered by phpBB © 2000, 2002, 2005, 2007 phpBB Group
http://www.phpbb.com/