Добрый вечер. помогите разобраться, есть 2 одинаковые карты и почему то с одинаковой неисправностью. на тесте матс-модс версии 455,400 в одной сборке, ошибки по всем каналам, на версии 367 матс вообще не запускается на команде -е, на команде -с не создает лог. segmentation fault пишет. сопротивления по памяти 150+ ом, pci-ex больше сотни, 1,8 килоомы. Биосы щелкал переключателем, ничего не меняется. Даже на 1 мб на 455й версии ошибки одинаковы, на одной из карт снимал канал А1, А0 - ровно столько же ошибок. Питания на памяти есть, шим сигнал правильной формы. mats 367.37 версии, может он слишком стар для нее? ссылку может на 37.106 есть у кого нибудь? не верю в смерть контроллера памяти с такими сопротивлениями и сразу на обеих картах, ГПУ цвета с завода. По модсу че то ругается на биос, но может изза версии модса это.


модс 367:

MODS start: Wed Jan 31 15:04:33 2024

Command Line : gputest.js -oqa -old_gold

CPU
Foundry : GenuineIntel
Name : Intel(R) Celeron(R) CPU G1840 @ 2.80GHz
Family : 6
Model : 12
Stepping : 3

Version
MODS : 367.38
OperatingSystem: Linux (x86_64)
Kernel : 4.1.2-gentoo
KernelDriver : 3.63
HostName : rt
Sys-uuid : 03000200-0400-0500-0006-000700080009

gpu 0 dev.sub 0.0
---------------------------
PCI Location : 0x00, 0x01, 0x00, 0x00
DID : 0x1c03
Raw ECID : 0x018065000000004023c10991
ECID : PG2F12-20_x06_y12
Device Id : GP106
Revision : a1
NV Base : 0xf6000000
FB Base : 0xe0000000
IRQ : 16
NV_PMC_INTR_0 bit 28 high.
Trying to clear interrupt by writing 0x0 to register 0x001140
NV_PMC_INTR_0 bit 28 high.
Trying to clear interrupt by writing 0x0 to register 0x001144
Successfully cleared GPU's interrupt state.

** ModsDrvBreakPoint **

------------------------- BEGIN ASSERT INFO DUMP -------------------------
register read: addr: 0x328730, regvalue: 0xbadcfed9, error code: Unknown SYS_PRI_ERROR_CODE
NVRM: STALE INTR_0_PRI_TIMEOUT pending on Initialization!
NVRM: reg read offset/data = 0x87118/0x0 to = 1
ACPI: Unable to evaluate dev method (_DOD) on 0:1:0.0
GF100GpuSubdevice: FloorsweepingAffected=0
GF100GpuSubdevice: Floorsweeping parameters present on commandline:
GF100GpuSubdevice: Floorsweeping parameter mask values: display=0x0 msdec=0x0 msvld=0x0 fbio_shift_override=0x0 ce=0x0 gpc=0x0 fb=0x0 fbio=0x0 fbio_shift=0x0 gpctpc[0]=0x0 gpctpc[1]=0x0 gpctpc[2]=0x0 gpctpc[3]=0x0 gpctpc[4]=0x0 gpctpc[5]=0x0 gpctpc[6]=0x0 gpctpc[7]=0x0 gpczcull[0]=0x0 gpczcull[1]=0x0 gpczcull[2]=0x0 gpczcull[3]=0x0 gpczcull[4]=0x0 gpczcull[5]=0x0 gpczcull[6]=0x0 gpczcull[7]=0x0
GF108PlusGpuSubdevice: Floorsweeping parameters present on commandline:
GF108PlusGpuSubdevice: Floorsweeping parameter mask values: pcie_lane=0x0 fbpa=0x0 spare=0x0
GM10xGpuSubdevice: Floorsweeping parameters present on commandline:
GM10xGpuSubdevice: Floorsweeping parameter mask values: nvenc=0x0 nvdec=0x0 head=0x0
GM20xGpuSubdevice: Floorsweeping parameters present on commandline:
GM20xGpuSubdevice: Floorsweeping parameters mask values: fbp_rop_l2[0]=0x0 fbp_rop_l2[1]=0x0 fbp_rop_l2[2]=0x0 fbp_rop_l2[3]=0x0 fbp_rop_l2[4]=0x0 fbp_rop_l2[5]=0x0 fbp_rop_l2[6]=0x0 fbp_rop_l2[7]=0x0 fbp_rop_l2[8]=0x0 fbp_rop_l2[9]=0x0 fbp_rop_l2[10]=0x0 fbp_rop_l2[11]=0x0 fbp_rop_l2[12]=0x0 fbp_rop_l2[13]=0x0 fbp_rop_l2[14]=0x0 fbp_rop_l2[15]=0x0
GP10xGpuSubdevice: Floorsweeping parameters present on commandline:
GP10xGpuSubdevice: Floorsweeping parameters mask values: gpc_pes[0]=0x0 gpc_pes[1]=0x0 gpc_pes[2]=0x0 gpc_pes[3]=0x0 gpc_pes[4]=0x0 gpc_pes[5]=0x0 gpc_pes[6]=0x0 gpc_pes[7]=0x0 gpc_pes[8]=0x0 gpc_pes[9]=0x0 gpc_pes[10]=0x0 gpc_pes[11]=0x0 gpc_pes[12]=0x0 gpc_pes[13]=0x0 gpc_pes[14]=0x0 gpc_pes[15]=0x0
NVRM: DevinitPmuOffloadDevinitToPmu Devinit complete is false
NVRM: bp @ ../../../../resman/kernel/devinit/nv/devinit_pmu.c:384

** ModsDrvBreakPoint **

-------------------------- END ASSERT INFO DUMP --------------------------

** ModsDrvBreakPoint **

------------------------- BEGIN ASSERT INFO DUMP -------------------------
ialization!
NVRM: reg read offset/data = 0x87118/0x0 to = 1
ACPI: Unable to evaluate dev method (_DOD) on 0:1:0.0
GF100GpuSubdevice: FloorsweepingAffected=0
GF100GpuSubdevice: Floorsweeping parameters present on commandline:
GF100GpuSubdevice: Floorsweeping parameter mask values: display=0x0 msdec=0x0 msvld=0x0 fbio_shift_override=0x0 ce=0x0 gpc=0x0 fb=0x0 fbio=0x0 fbio_shift=0x0 gpctpc[0]=0x0 gpctpc[1]=0x0 gpctpc[2]=0x0 gpctpc[3]=0x0 gpctpc[4]=0x0 gpctpc[5]=0x0 gpctpc[6]=0x0 gpctpc[7]=0x0 gpczcull[0]=0x0 gpczcull[1]=0x0 gpczcull[2]=0x0 gpczcull[3]=0x0 gpczcull[4]=0x0 gpczcull[5]=0x0 gpczcull[6]=0x0 gpczcull[7]=0x0
GF108PlusGpuSubdevice: Floorsweeping parameters present on commandline:
GF108PlusGpuSubdevice: Floorsweeping parameter mask values: pcie_lane=0x0 fbpa=0x0 spare=0x0
GM10xGpuSubdevice: Floorsweeping parameters present on commandline:
GM10xGpuSubdevice: Floorsweeping parameter mask values: nvenc=0x0 nvdec=0x0 head=0x0
GM20xGpuSubdevice: Floorsweeping parameters present on commandline:
GM20xGpuSubdevice: Floorsweeping parameters mask values: fbp_rop_l2[0]=0x0 fbp_rop_l2[1]=0x0 fbp_rop_l2[2]=0x0 fbp_rop_l2[3]=0x0 fbp_rop_l2[4]=0x0 fbp_rop_l2[5]=0x0 fbp_rop_l2[6]=0x0 fbp_rop_l2[7]=0x0 fbp_rop_l2[8]=0x0 fbp_rop_l2[9]=0x0 fbp_rop_l2[10]=0x0 fbp_rop_l2[11]=0x0 fbp_rop_l2[12]=0x0 fbp_rop_l2[13]=0x0 fbp_rop_l2[14]=0x0 fbp_rop_l2[15]=0x0
GP10xGpuSubdevice: Floorsweeping parameters present on commandline:
GP10xGpuSubdevice: Floorsweeping parameters mask values: gpc_pes[0]=0x0 gpc_pes[1]=0x0 gpc_pes[2]=0x0 gpc_pes[3]=0x0 gpc_pes[4]=0x0 gpc_pes[5]=0x0 gpc_pes[6]=0x0 gpc_pes[7]=0x0 gpc_pes[8]=0x0 gpc_pes[9]=0x0 gpc_pes[10]=0x0 gpc_pes[11]=0x0 gpc_pes[12]=0x0 gpc_pes[13]=0x0 gpc_pes[14]=0x0 gpc_pes[15]=0x0
NVRM: DevinitPmuOffloadDevinitToPmu Devinit complete is false
NVRM: bp @ ../../../../resman/kernel/devinit/nv/devinit_pmu.c:384

** ModsDrvBreakPoint **
NVRM: Devinit on PMU failed to execute correctly!!
NVRM: bp @ ../../../../resman/kernel/devinit/nv/devinit.c:1063

** ModsDrvBreakPoint **

-------------------------- END ASSERT INFO DUMP --------------------------

** ModsDrvBreakPoint **

------------------------- BEGIN ASSERT INFO DUMP -------------------------
INFO_RAM_TYPE _GDDR5 (0x08) does not match NV_PFB_FBPA_FBIO_BROADCAST_DDR_MODE=0x00.
NVRM: Possible bad register read: addr: 0x9a0590, regvalue: 0xbadf3000, error code: NV_PPRIV_SYS_PRI_ERROR_CODE_FECS_DEAD_RING
NVRM: Possible bad register read: addr: 0x9a0590, regvalue: 0xbadf3000, error code: NV_PPRIV_SYS_PRI_ERROR_CODE_FECS_DEAD_RING
NVRM: Possible bad register read: addr: 0x9a0470, regvalue: 0xbadf3000, error code: NV_PPRIV_SYS_PRI_ERROR_CODE_FECS_DEAD_RING
NVRM: Possible bad register read: addr: 0x9a0470, regvalue: 0xbadf3000, error code: NV_PPRIV_SYS_PRI_ERROR_CODE_FECS_DEAD_RING
NVRM: Possible bad register read: addr: 0x9a0470, regvalue: 0xbadf3000, error code: NV_PPRIV_SYS_PRI_ERROR_CODE_FECS_DEAD_RING
NVRM: Possible bad register read: addr: 0x9a0470, regvalue: 0xbadf3000, error code: NV_PPRIV_SYS_PRI_ERROR_CODE_FECS_DEAD_RING
NVRM: Possible bad register read: addr: 0x17e318, regvalue: 0xbadf3000, error code: NV_PPRIV_SYS_PRI_ERROR_CODE_FECS_DEAD_RING
NVRM: Possible bad register read: addr: 0x9a050c, regvalue: 0xbadf3000, error code: NV_PPRIV_SYS_PRI_ERROR_CODE_FECS_DEAD_RING
NVRM: Possible bad register read: addr: 0x9a050c, regvalue: 0xbadf3000, error code: NV_PPRIV_SYS_PRI_ERROR_CODE_FECS_DEAD_RING
NVRM: inforomBBXLoadObject_IMPL: BBX object get failed, status=0x57
NVRM: *** Chipset Setup Function Error!
NVRM: inforomGetPPOObject: InfoROM PPO object header load failed, status=0x57
NVRM: clkRead_Finish_Mux: utilsclk.osm3.mux[0]: NV_ERR_INVALID_STATE: Active input 0 is not attached in the schematic.
NVRM: clkRead_Finish_Mux: NV_PTRIM_SYS_UTILSCLK_OUT_SWITCH: addr=0x0013718c cache=valid data=0x00000002 prev=0x00000002
NVRM: clkReadDomain_CLK2: utilsclk: Error reading clock domain (23). NV_STATUS=0x00000040
NVRM: clkReadDomain_CLK2: output.freqKHz=0KHz path=0xffffffff spread=2 fracdiv=255 hot=0
NVRM: _DevinitGetVoltageDeviceTable_1X_PSV: Failed to map PWM frequency: 675000 to raw period!
NVRM: bp @ ../../../../resman/kernel/devinit/nv/devinit_volt.c:4089

** ModsDrvBreakPoint **

-------------------------- END ASSERT INFO DUMP --------------------------

** ModsDrvBreakPoint **

------------------------- BEGIN ASSERT INFO DUMP -------------------------
0xbadf3000, error code: NV_PPRIV_SYS_PRI_ERROR_CODE_FECS_DEAD_RING
NVRM: Possible bad register read: addr: 0x9a0470, regvalue: 0xbadf3000, error code: NV_PPRIV_SYS_PRI_ERROR_CODE_FECS_DEAD_RING
NVRM: Possible bad register read: addr: 0x9a0470, regvalue: 0xbadf3000, error code: NV_PPRIV_SYS_PRI_ERROR_CODE_FECS_DEAD_RING
NVRM: Possible bad register read: addr: 0x9a0470, regvalue: 0xbadf3000, error code: NV_PPRIV_SYS_PRI_ERROR_CODE_FECS_DEAD_RING
NVRM: Possible bad register read: addr: 0x9a0470, regvalue: 0xbadf3000, error code: NV_PPRIV_SYS_PRI_ERROR_CODE_FECS_DEAD_RING
NVRM: Possible bad register read: addr: 0x17e318, regvalue: 0xbadf3000, error code: NV_PPRIV_SYS_PRI_ERROR_CODE_FECS_DEAD_RING
NVRM: Possible bad register read: addr: 0x9a050c, regvalue: 0xbadf3000, error code: NV_PPRIV_SYS_PRI_ERROR_CODE_FECS_DEAD_RING
NVRM: Possible bad register read: addr: 0x9a050c, regvalue: 0xbadf3000, error code: NV_PPRIV_SYS_PRI_ERROR_CODE_FECS_DEAD_RING
NVRM: inforomBBXLoadObject_IMPL: BBX object get failed, status=0x57
NVRM: *** Chipset Setup Function Error!
NVRM: inforomGetPPOObject: InfoROM PPO object header load failed, status=0x57
NVRM: clkRead_Finish_Mux: utilsclk.osm3.mux[0]: NV_ERR_INVALID_STATE: Active input 0 is not attached in the schematic.
NVRM: clkRead_Finish_Mux: NV_PTRIM_SYS_UTILSCLK_OUT_SWITCH: addr=0x0013718c cache=valid data=0x00000002 prev=0x00000002
NVRM: clkReadDomain_CLK2: utilsclk: Error reading clock domain (23). NV_STATUS=0x00000040
NVRM: clkReadDomain_CLK2: output.freqKHz=0KHz path=0xffffffff spread=2 fracdiv=255 hot=0
NVRM: _DevinitGetVoltageDeviceTable_1X_PSV: Failed to map PWM frequency: 675000 to raw period!
NVRM: bp @ ../../../../resman/kernel/devinit/nv/devinit_volt.c:4089

** ModsDrvBreakPoint **
NVRM: Possible bad register read: addr: 0x214a8, regvalue: 0xbadf510c, error code: Unknown SYS_PRI_ERROR_CODE
NVRM: DevinitGetVoltageDescriptorTable: Unrecognized version (0x30)
NVRM: bp @ ../../../../resman/kernel/devinit/nv/devinit_volt.c:3257

** ModsDrvBreakPoint **

-------------------------- END ASSERT INFO DUMP --------------------------

** ModsDrvBreakPoint **

------------------------- BEGIN ASSERT INFO DUMP -------------------------
ROR_CODE_FECS_DEAD_RING
NVRM: Possible bad register read: addr: 0x9a0470, regvalue: 0xbadf3000, error code: NV_PPRIV_SYS_PRI_ERROR_CODE_FECS_DEAD_RING
NVRM: Possible bad register read: addr: 0x9a0470, regvalue: 0xbadf3000, error code: NV_PPRIV_SYS_PRI_ERROR_CODE_FECS_DEAD_RING
NVRM: Possible bad register read: addr: 0x9a0470, regvalue: 0xbadf3000, error code: NV_PPRIV_SYS_PRI_ERROR_CODE_FECS_DEAD_RING
NVRM: Possible bad register read: addr: 0x17e318, regvalue: 0xbadf3000, error code: NV_PPRIV_SYS_PRI_ERROR_CODE_FECS_DEAD_RING
NVRM: Possible bad register read: addr: 0x9a050c, regvalue: 0xbadf3000, error code: NV_PPRIV_SYS_PRI_ERROR_CODE_FECS_DEAD_RING
NVRM: Possible bad register read: addr: 0x9a050c, regvalue: 0xbadf3000, error code: NV_PPRIV_SYS_PRI_ERROR_CODE_FECS_DEAD_RING
NVRM: inforomBBXLoadObject_IMPL: BBX object get failed, status=0x57
NVRM: *** Chipset Setup Function Error!
NVRM: inforomGetPPOObject: InfoROM PPO object header load failed, status=0x57
NVRM: clkRead_Finish_Mux: utilsclk.osm3.mux[0]: NV_ERR_INVALID_STATE: Active input 0 is not attached in the schematic.
NVRM: clkRead_Finish_Mux: NV_PTRIM_SYS_UTILSCLK_OUT_SWITCH: addr=0x0013718c cache=valid data=0x00000002 prev=0x00000002
NVRM: clkReadDomain_CLK2: utilsclk: Error reading clock domain (23). NV_STATUS=0x00000040
NVRM: clkReadDomain_CLK2: output.freqKHz=0KHz path=0xffffffff spread=2 fracdiv=255 hot=0
NVRM: _DevinitGetVoltageDeviceTable_1X_PSV: Failed to map PWM frequency: 675000 to raw period!
NVRM: bp @ ../../../../resman/kernel/devinit/nv/devinit_volt.c:4089

** ModsDrvBreakPoint **
NVRM: Possible bad register read: addr: 0x214a8, regvalue: 0xbadf510c, error code: Unknown SYS_PRI_ERROR_CODE
NVRM: DevinitGetVoltageDescriptorTable: Unrecognized version (0x30)
NVRM: bp @ ../../../../resman/kernel/devinit/nv/devinit_volt.c:3257

** ModsDrvBreakPoint **
NVRM: _voltGetVoltageDescriptorTable: Error parsing the VDT from VBIOS: status = 0x00000056
NVRM: bp @ ../../../../resman/kernel/pmgr/nv/vdt.c:2932

** ModsDrvBreakPoint **

-------------------------- END ASSERT INFO DUMP --------------------------

** ModsDrvBreakPoint **

------------------------- BEGIN ASSERT INFO DUMP -------------------------
VRM: Possible bad register read: addr: 0x9a0470, regvalue: 0xbadf3000, error code: NV_PPRIV_SYS_PRI_ERROR_CODE_FECS_DEAD_RING
NVRM: Possible bad register read: addr: 0x9a0470, regvalue: 0xbadf3000, error code: NV_PPRIV_SYS_PRI_ERROR_CODE_FECS_DEAD_RING
NVRM: Possible bad register read: addr: 0x17e318, regvalue: 0xbadf3000, error code: NV_PPRIV_SYS_PRI_ERROR_CODE_FECS_DEAD_RING
NVRM: Possible bad register read: addr: 0x9a050c, regvalue: 0xbadf3000, error code: NV_PPRIV_SYS_PRI_ERROR_CODE_FECS_DEAD_RING
NVRM: Possible bad register read: addr: 0x9a050c, regvalue: 0xbadf3000, error code: NV_PPRIV_SYS_PRI_ERROR_CODE_FECS_DEAD_RING
NVRM: inforomBBXLoadObject_IMPL: BBX object get failed, status=0x57
NVRM: *** Chipset Setup Function Error!
NVRM: inforomGetPPOObject: InfoROM PPO object header load failed, status=0x57
NVRM: clkRead_Finish_Mux: utilsclk.osm3.mux[0]: NV_ERR_INVALID_STATE: Active input 0 is not attached in the schematic.
NVRM: clkRead_Finish_Mux: NV_PTRIM_SYS_UTILSCLK_OUT_SWITCH: addr=0x0013718c cache=valid data=0x00000002 prev=0x00000002
NVRM: clkReadDomain_CLK2: utilsclk: Error reading clock domain (23). NV_STATUS=0x00000040
NVRM: clkReadDomain_CLK2: output.freqKHz=0KHz path=0xffffffff spread=2 fracdiv=255 hot=0
NVRM: _DevinitGetVoltageDeviceTable_1X_PSV: Failed to map PWM frequency: 675000 to raw period!
NVRM: bp @ ../../../../resman/kernel/devinit/nv/devinit_volt.c:4089

** ModsDrvBreakPoint **
NVRM: Possible bad register read: addr: 0x214a8, regvalue: 0xbadf510c, error code: Unknown SYS_PRI_ERROR_CODE
NVRM: DevinitGetVoltageDescriptorTable: Unrecognized version (0x30)
NVRM: bp @ ../../../../resman/kernel/devinit/nv/devinit_volt.c:3257

** ModsDrvBreakPoint **
NVRM: _voltGetVoltageDescriptorTable: Error parsing the VDT from VBIOS: status = 0x00000056
NVRM: bp @ ../../../../resman/kernel/pmgr/nv/vdt.c:2932

** ModsDrvBreakPoint **
NVRM: voltVdtStateInit_IMPL: Error fetching the VDT: status = 0x00000056
NVRM: bp @ ../../../../resman/kernel/pmgr/nv/vdt.c:120

** ModsDrvBreakPoint **

-------------------------- END ASSERT INFO DUMP --------------------------

** ModsDrvBreakPoint **

------------------------- BEGIN ASSERT INFO DUMP -------------------------
000, error code: NV_PPRIV_SYS_PRI_ERROR_CODE_FECS_DEAD_RING
NVRM: Possible bad register read: addr: 0x17e318, regvalue: 0xbadf3000, error code: NV_PPRIV_SYS_PRI_ERROR_CODE_FECS_DEAD_RING
NVRM: Possible bad register read: addr: 0x9a050c, regvalue: 0xbadf3000, error code: NV_PPRIV_SYS_PRI_ERROR_CODE_FECS_DEAD_RING
NVRM: Possible bad register read: addr: 0x9a050c, regvalue: 0xbadf3000, error code: NV_PPRIV_SYS_PRI_ERROR_CODE_FECS_DEAD_RING
NVRM: inforomBBXLoadObject_IMPL: BBX object get failed, status=0x57
NVRM: *** Chipset Setup Function Error!
NVRM: inforomGetPPOObject: InfoROM PPO object header load failed, status=0x57
NVRM: clkRead_Finish_Mux: utilsclk.osm3.mux[0]: NV_ERR_INVALID_STATE: Active input 0 is not attached in the schematic.
NVRM: clkRead_Finish_Mux: NV_PTRIM_SYS_UTILSCLK_OUT_SWITCH: addr=0x0013718c cache=valid data=0x00000002 prev=0x00000002
NVRM: clkReadDomain_CLK2: utilsclk: Error reading clock domain (23). NV_STATUS=0x00000040
NVRM: clkReadDomain_CLK2: output.freqKHz=0KHz path=0xffffffff spread=2 fracdiv=255 hot=0
NVRM: _DevinitGetVoltageDeviceTable_1X_PSV: Failed to map PWM frequency: 675000 to raw period!
NVRM: bp @ ../../../../resman/kernel/devinit/nv/devinit_volt.c:4089

** ModsDrvBreakPoint **
NVRM: Possible bad register read: addr: 0x214a8, regvalue: 0xbadf510c, error code: Unknown SYS_PRI_ERROR_CODE
NVRM: DevinitGetVoltageDescriptorTable: Unrecognized version (0x30)
NVRM: bp @ ../../../../resman/kernel/devinit/nv/devinit_volt.c:3257

** ModsDrvBreakPoint **
NVRM: _voltGetVoltageDescriptorTable: Error parsing the VDT from VBIOS: status = 0x00000056
NVRM: bp @ ../../../../resman/kernel/pmgr/nv/vdt.c:2932

** ModsDrvBreakPoint **
NVRM: voltVdtStateInit_IMPL: Error fetching the VDT: status = 0x00000056
NVRM: bp @ ../../../../resman/kernel/pmgr/nv/vdt.c:120

** ModsDrvBreakPoint **
NVRM: voltVoltDeviceLegacyStateInit_IMPL: Failed to obtain Power Control Table from VBIOS. status = 0x0000ffff
NVRM: bp @ ../../../../resman/kernel/pmgr/nv/voltdev.c:198

** ModsDrvBreakPoint **

-------------------------- END ASSERT INFO DUMP --------------------------

** ModsDrvBreakPoint **

------------------------- BEGIN ASSERT INFO DUMP -------------------------
RING
NVRM: Possible bad register read: addr: 0x9a050c, regvalue: 0xbadf3000, error code: NV_PPRIV_SYS_PRI_ERROR_CODE_FECS_DEAD_RING
NVRM: Possible bad register read: addr: 0x9a050c, regvalue: 0xbadf3000, error code: NV_PPRIV_SYS_PRI_ERROR_CODE_FECS_DEAD_RING
NVRM: inforomBBXLoadObject_IMPL: BBX object get failed, status=0x57
NVRM: *** Chipset Setup Function Error!
NVRM: inforomGetPPOObject: InfoROM PPO object header load failed, status=0x57
NVRM: clkRead_Finish_Mux: utilsclk.osm3.mux[0]: NV_ERR_INVALID_STATE: Active input 0 is not attached in the schematic.
NVRM: clkRead_Finish_Mux: NV_PTRIM_SYS_UTILSCLK_OUT_SWITCH: addr=0x0013718c cache=valid data=0x00000002 prev=0x00000002
NVRM: clkReadDomain_CLK2: utilsclk: Error reading clock domain (23). NV_STATUS=0x00000040
NVRM: clkReadDomain_CLK2: output.freqKHz=0KHz path=0xffffffff spread=2 fracdiv=255 hot=0
NVRM: _DevinitGetVoltageDeviceTable_1X_PSV: Failed to map PWM frequency: 675000 to raw period!
NVRM: bp @ ../../../../resman/kernel/devinit/nv/devinit_volt.c:4089

** ModsDrvBreakPoint **
NVRM: Possible bad register read: addr: 0x214a8, regvalue: 0xbadf510c, error code: Unknown SYS_PRI_ERROR_CODE
NVRM: DevinitGetVoltageDescriptorTable: Unrecognized version (0x30)
NVRM: bp @ ../../../../resman/kernel/devinit/nv/devinit_volt.c:3257

** ModsDrvBreakPoint **
NVRM: _voltGetVoltageDescriptorTable: Error parsing the VDT from VBIOS: status = 0x00000056
NVRM: bp @ ../../../../resman/kernel/pmgr/nv/vdt.c:2932

** ModsDrvBreakPoint **
NVRM: voltVdtStateInit_IMPL: Error fetching the VDT: status = 0x00000056
NVRM: bp @ ../../../../resman/kernel/pmgr/nv/vdt.c:120

** ModsDrvBreakPoint **
NVRM: voltVoltDeviceLegacyStateInit_IMPL: Failed to obtain Power Control Table from VBIOS. status = 0x0000ffff
NVRM: bp @ ../../../../resman/kernel/pmgr/nv/voltdev.c:198

** ModsDrvBreakPoint **
NVRM: voltStateInitLocked_IMPL: Error initializing SW state for VOLTAGE_DEVICE. status = 0x0000ffff
NVRM: bp @ ../../../../resman/kernel/pmgr/nv/objvolt.c:192

** ModsDrvBreakPoint **

-------------------------- END ASSERT INFO DUMP --------------------------
Error 000000000229 : Gpu.Initialize hardware was not initialized
Error 000000000229 : Global.PrintGpuInitError hardware was not initialized
Error 000000000229 : Global.InitializeGpuTests hardware was not initialized

Error Code = 000000000818 (Mods detected an assertion failure)


####### #### ######## ###
####### ###### ######## ###
## ## ## ## ###
## ## ## ## ###
####### ######## ## ###
####### ######## ## ###
## ## ## ## ###
## ## ## ######## ########
## ## ## ######## ########


MODS end : Wed Jan 31 15:04:37 2024 [4.034 seconds (00:00:04.034 h:m:s)]

В последний раз когда были две карты от одного клиента с одинаковой неисправностью (правда ошибки по двум разным чипам, но по одним и тем же на двух одинаковых устройствах) дело оказалось банально в прошивке, клиент умолчал о том что пытался шить, в результате потраченное время на поиск несуществующей неисправности. проверьте на всякий!

так же стоит проверть дроссель LB501 (на Asus 1060 dual так называется, может у вас схожие позиционные обозначения). если с ним проблемы, то может такой эффект присутствовать.

судя по борде от дуала,LB501 это не дроссель. И если по скрину это он, то тут расположение элементов не совпадает

По борде это именно он). Но расположение вполне может отличаться, вендоры все таки разные.
Поищите на своей доске(мб этот участок как то по другому сформирован на вашей карте вовсе).

не поверите, но на обеих картах что то нашел.на одной пайка нелепая, я ее видел,но повызванивал и не придал значения до этого, а на второй 2 сломаных кондера нашел. сравнив, понял что на карте с чудо пайкой вместо дросселя кондер стоит. а на нормальной они оба живы, звонятся на 1,8 Вольта, и 0 ом сопротивление. Судя по всему это оно. Попаять только завтра смогу. А в чем важность этих дросселей? за что они отвечают??

Есть результат?

на одной восстановил как должно быть,но ничего не изменилось.снял гпу,хочу на другую доску подкинуть для верности.вечером отпишусь о результате

вобщем ГПУшка жива. пересадил и все заработало. Может есть у кого нибудь номинал сбитого кондера? может он не такой как надо стоял

22uf

на перепаяной стоял на 10, это могло как то повлиять?

Я думаю что как минимум не стоит недооценивать то, насколько критичной порой бывает просадка емкости конденсатора более чем в два раза от той что указана в схеме и уж тем более важность той цепи в которой он стоит. Между тем это самый емкий конденсатор в цепи 1V8_FB_PLL из всех присутствующих. Тоже самое касается и 1V8_GPC_SP_VID_PLL. Также еще нужно понимать что с запасом никто ничего ставить не будет, это слишком удорожает производство конечного продукта.

восстановил кондеры но толку не стало, прошил оба биоса-результат=0. модс 367.106 и матс запускал,не пойму что там ругается на биос



MODS start: Mon Feb 5 10:55:51 2024

Command Line : gputest.js -oqa -old_gold

CPU
Foundry : GenuineIntel
Name : Intel(R) Celeron(R) CPU G1840 @ 2.80GHz
Family : 6
Model : 12
Stepping : 3

Version
MODS : 367.106
OperatingSystem: Linux (x86_64)
Kernel : 4.1.2-gentoo
KernelDriver : 3.63
HostName : rt
Sys-uuid : 03000200-0400-0500-0006-000700080009

GPU 0 [01:00.0] dev.sub 0.0
---------------------------
PCI Location : 0x00, 0x01, 0x00, 0x00
DID : 0x1c03
Raw ECID : 0x00000000018065000000004023c10991
Raw ECID (GHS) : 0x00000001644023c10800000014030300
ECID : PG2F12-20_x06_y12
Device Id : GP106
Revision : a1
NV Base : 0xf6000000
FB Base : 0xe0000000
IRQ : 16
NV_PMC_INTR_0 bit 28 high.
Trying to clear interrupt by writing 0x0 to register 0x001140
NV_PMC_INTR_0 bit 28 high.
Trying to clear interrupt by writing 0x0 to register 0x001144
Successfully cleared GPU's interrupt state.

** ModsDrvBreakPoint **

------------------------- BEGIN ASSERT INFO DUMP -------------------------
egister read: addr: 0x324288, regvalue: 0xbadfd623, error code: Unknown SYS_PRI_ERROR_CODE
NVRM: STALE INTR_0_PRI_TIMEOUT pending on Initialization!
NVRM: reg read offset/data = 0x9a0590/0x0 to = 1
ACPI: Unable to evaluate dev method (_DOD) on 0:1:0.0
GF100GpuSubdevice: FloorsweepingAffected=0
GF100GpuSubdevice: Floorsweeping parameters present on commandline:
GF100GpuSubdevice: Floorsweeping parameter mask values: display=0x0 msdec=0x0 msvld=0x0 fbio_shift_override=0x0 ce=0x0 gpc=0x0 fb=0x0 fbio=0x0 fbio_shift=0x0 gpctpc[0]=0x0 gpctpc[1]=0x0 gpctpc[2]=0x0 gpctpc[3]=0x0 gpctpc[4]=0x0 gpctpc[5]=0x0 gpctpc[6]=0x0 gpctpc[7]=0x0 gpczcull[0]=0x0 gpczcull[1]=0x0 gpczcull[2]=0x0 gpczcull[3]=0x0 gpczcull[4]=0x0 gpczcull[5]=0x0 gpczcull[6]=0x0 gpczcull[7]=0x0
GF108PlusGpuSubdevice: Floorsweeping parameters present on commandline:
GF108PlusGpuSubdevice: Floorsweeping parameter mask values: pcie_lane=0x0 fbpa=0x0 spare=0x0
GM10xGpuSubdevice: Floorsweeping parameters present on commandline:
GM10xGpuSubdevice: Floorsweeping parameter mask values: nvenc=0x0 nvdec=0x0 head=0x0
GM20xGpuSubdevice: Floorsweeping parameters present on commandline:
GM20xGpuSubdevice: Floorsweeping parameters mask values: fbp_rop_l2[0]=0x0 fbp_rop_l2[1]=0x0 fbp_rop_l2[2]=0x0 fbp_rop_l2[3]=0x0 fbp_rop_l2[4]=0x0 fbp_rop_l2[5]=0x0 fbp_rop_l2[6]=0x0 fbp_rop_l2[7]=0x0 fbp_rop_l2[8]=0x0 fbp_rop_l2[9]=0x0 fbp_rop_l2[10]=0x0 fbp_rop_l2[11]=0x0 fbp_rop_l2[12]=0x0 fbp_rop_l2[13]=0x0 fbp_rop_l2[14]=0x0 fbp_rop_l2[15]=0x0
GP10xGpuSubdevice: Floorsweeping parameters present on commandline:
GP10xGpuSubdevice: Floorsweeping parameters mask values: gpc_pes[0]=0x0 gpc_pes[1]=0x0 gpc_pes[2]=0x0 gpc_pes[3]=0x0 gpc_pes[4]=0x0 gpc_pes[5]=0x0 gpc_pes[6]=0x0 gpc_pes[7]=0x0 gpc_pes[8]=0x0 gpc_pes[9]=0x0 gpc_pes[10]=0x0 gpc_pes[11]=0x0 gpc_pes[12]=0x0 gpc_pes[13]=0x0 gpc_pes[14]=0x0 gpc_pes[15]=0x0
NVRM: DevinitPmuOffloadDevinitToPmu Devinit complete is false
NVRM: bp @ ../../../../resman/kernel/devinit/nv/devinit_pmu.c:391

** ModsDrvBreakPoint **

-------------------------- END ASSERT INFO DUMP --------------------------

** ModsDrvBreakPoint **

------------------------- BEGIN ASSERT INFO DUMP -------------------------
alization!
NVRM: reg read offset/data = 0x9a0590/0x0 to = 1
ACPI: Unable to evaluate dev method (_DOD) on 0:1:0.0
GF100GpuSubdevice: FloorsweepingAffected=0
GF100GpuSubdevice: Floorsweeping parameters present on commandline:
GF100GpuSubdevice: Floorsweeping parameter mask values: display=0x0 msdec=0x0 msvld=0x0 fbio_shift_override=0x0 ce=0x0 gpc=0x0 fb=0x0 fbio=0x0 fbio_shift=0x0 gpctpc[0]=0x0 gpctpc[1]=0x0 gpctpc[2]=0x0 gpctpc[3]=0x0 gpctpc[4]=0x0 gpctpc[5]=0x0 gpctpc[6]=0x0 gpctpc[7]=0x0 gpczcull[0]=0x0 gpczcull[1]=0x0 gpczcull[2]=0x0 gpczcull[3]=0x0 gpczcull[4]=0x0 gpczcull[5]=0x0 gpczcull[6]=0x0 gpczcull[7]=0x0
GF108PlusGpuSubdevice: Floorsweeping parameters present on commandline:
GF108PlusGpuSubdevice: Floorsweeping parameter mask values: pcie_lane=0x0 fbpa=0x0 spare=0x0
GM10xGpuSubdevice: Floorsweeping parameters present on commandline:
GM10xGpuSubdevice: Floorsweeping parameter mask values: nvenc=0x0 nvdec=0x0 head=0x0
GM20xGpuSubdevice: Floorsweeping parameters present on commandline:
GM20xGpuSubdevice: Floorsweeping parameters mask values: fbp_rop_l2[0]=0x0 fbp_rop_l2[1]=0x0 fbp_rop_l2[2]=0x0 fbp_rop_l2[3]=0x0 fbp_rop_l2[4]=0x0 fbp_rop_l2[5]=0x0 fbp_rop_l2[6]=0x0 fbp_rop_l2[7]=0x0 fbp_rop_l2[8]=0x0 fbp_rop_l2[9]=0x0 fbp_rop_l2[10]=0x0 fbp_rop_l2[11]=0x0 fbp_rop_l2[12]=0x0 fbp_rop_l2[13]=0x0 fbp_rop_l2[14]=0x0 fbp_rop_l2[15]=0x0
GP10xGpuSubdevice: Floorsweeping parameters present on commandline:
GP10xGpuSubdevice: Floorsweeping parameters mask values: gpc_pes[0]=0x0 gpc_pes[1]=0x0 gpc_pes[2]=0x0 gpc_pes[3]=0x0 gpc_pes[4]=0x0 gpc_pes[5]=0x0 gpc_pes[6]=0x0 gpc_pes[7]=0x0 gpc_pes[8]=0x0 gpc_pes[9]=0x0 gpc_pes[10]=0x0 gpc_pes[11]=0x0 gpc_pes[12]=0x0 gpc_pes[13]=0x0 gpc_pes[14]=0x0 gpc_pes[15]=0x0
NVRM: DevinitPmuOffloadDevinitToPmu Devinit complete is false
NVRM: bp @ ../../../../resman/kernel/devinit/nv/devinit_pmu.c:391

** ModsDrvBreakPoint **
NVRM: Devinit on PMU failed to execute correctly!!
NVRM: bp @ ../../../../resman/kernel/devinit/nv/devinit.c:1063

** ModsDrvBreakPoint **

-------------------------- END ASSERT INFO DUMP --------------------------

** ModsDrvBreakPoint **

------------------------- BEGIN ASSERT INFO DUMP -------------------------
INFO_RAM_TYPE _GDDR5 (0x08) does not match NV_PFB_FBPA_FBIO_BROADCAST_DDR_MODE=0x00.
NVRM: Possible bad register read: addr: 0x9a0590, regvalue: 0xbadf3000, error code: NV_PPRIV_SYS_PRI_ERROR_CODE_FECS_DEAD_RING
NVRM: Possible bad register read: addr: 0x9a0590, regvalue: 0xbadf3000, error code: NV_PPRIV_SYS_PRI_ERROR_CODE_FECS_DEAD_RING
NVRM: Possible bad register read: addr: 0x9a0470, regvalue: 0xbadf3000, error code: NV_PPRIV_SYS_PRI_ERROR_CODE_FECS_DEAD_RING
NVRM: Possible bad register read: addr: 0x9a0470, regvalue: 0xbadf3000, error code: NV_PPRIV_SYS_PRI_ERROR_CODE_FECS_DEAD_RING
NVRM: Possible bad register read: addr: 0x9a0470, regvalue: 0xbadf3000, error code: NV_PPRIV_SYS_PRI_ERROR_CODE_FECS_DEAD_RING
NVRM: Possible bad register read: addr: 0x9a0470, regvalue: 0xbadf3000, error code: NV_PPRIV_SYS_PRI_ERROR_CODE_FECS_DEAD_RING
NVRM: Possible bad register read: addr: 0x17e318, regvalue: 0xbadf3000, error code: NV_PPRIV_SYS_PRI_ERROR_CODE_FECS_DEAD_RING
NVRM: Possible bad register read: addr: 0x9a050c, regvalue: 0xbadf3000, error code: NV_PPRIV_SYS_PRI_ERROR_CODE_FECS_DEAD_RING
NVRM: Possible bad register read: addr: 0x9a050c, regvalue: 0xbadf3000, error code: NV_PPRIV_SYS_PRI_ERROR_CODE_FECS_DEAD_RING
NVRM: inforomBBXLoadObject_IMPL: BBX object get failed, status=0x57
NVRM: *** Chipset Setup Function Error!
NVRM: inforomGetPPOObject: InfoROM PPO object header load failed, status=0x57
NVRM: clkRead_Finish_Mux: utilsclk.osm3.mux[0]: NV_ERR_INVALID_STATE: Active input 0 is not attached in the schematic.
NVRM: clkRead_Finish_Mux: NV_PTRIM_SYS_UTILSCLK_OUT_SWITCH: addr=0x0013718c cache=valid data=0x00000002 prev=0x00000002
NVRM: clkReadDomain_CLK2: utilsclk: Error reading clock domain (23). NV_STATUS=0x00000040
NVRM: clkReadDomain_CLK2: output.freqKHz=0KHz path=0xffffffff spread=2 fracdiv=255 hot=0
NVRM: _DevinitGetVoltageDeviceTable_1X_PSV: Failed to map PWM frequency: 675000 to raw period!
NVRM: bp @ ../../../../resman/kernel/devinit/nv/devinit_volt.c:4089

** ModsDrvBreakPoint **

-------------------------- END ASSERT INFO DUMP --------------------------

** ModsDrvBreakPoint **

------------------------- BEGIN ASSERT INFO DUMP -------------------------
0xbadf3000, error code: NV_PPRIV_SYS_PRI_ERROR_CODE_FECS_DEAD_RING
NVRM: Possible bad register read: addr: 0x9a0470, regvalue: 0xbadf3000, error code: NV_PPRIV_SYS_PRI_ERROR_CODE_FECS_DEAD_RING
NVRM: Possible bad register read: addr: 0x9a0470, regvalue: 0xbadf3000, error code: NV_PPRIV_SYS_PRI_ERROR_CODE_FECS_DEAD_RING
NVRM: Possible bad register read: addr: 0x9a0470, regvalue: 0xbadf3000, error code: NV_PPRIV_SYS_PRI_ERROR_CODE_FECS_DEAD_RING
NVRM: Possible bad register read: addr: 0x9a0470, regvalue: 0xbadf3000, error code: NV_PPRIV_SYS_PRI_ERROR_CODE_FECS_DEAD_RING
NVRM: Possible bad register read: addr: 0x17e318, regvalue: 0xbadf3000, error code: NV_PPRIV_SYS_PRI_ERROR_CODE_FECS_DEAD_RING
NVRM: Possible bad register read: addr: 0x9a050c, regvalue: 0xbadf3000, error code: NV_PPRIV_SYS_PRI_ERROR_CODE_FECS_DEAD_RING
NVRM: Possible bad register read: addr: 0x9a050c, regvalue: 0xbadf3000, error code: NV_PPRIV_SYS_PRI_ERROR_CODE_FECS_DEAD_RING
NVRM: inforomBBXLoadObject_IMPL: BBX object get failed, status=0x57
NVRM: *** Chipset Setup Function Error!
NVRM: inforomGetPPOObject: InfoROM PPO object header load failed, status=0x57
NVRM: clkRead_Finish_Mux: utilsclk.osm3.mux[0]: NV_ERR_INVALID_STATE: Active input 0 is not attached in the schematic.
NVRM: clkRead_Finish_Mux: NV_PTRIM_SYS_UTILSCLK_OUT_SWITCH: addr=0x0013718c cache=valid data=0x00000002 prev=0x00000002
NVRM: clkReadDomain_CLK2: utilsclk: Error reading clock domain (23). NV_STATUS=0x00000040
NVRM: clkReadDomain_CLK2: output.freqKHz=0KHz path=0xffffffff spread=2 fracdiv=255 hot=0
NVRM: _DevinitGetVoltageDeviceTable_1X_PSV: Failed to map PWM frequency: 675000 to raw period!
NVRM: bp @ ../../../../resman/kernel/devinit/nv/devinit_volt.c:4089

** ModsDrvBreakPoint **
NVRM: Possible bad register read: addr: 0x214a8, regvalue: 0xbadf510c, error code: Unknown SYS_PRI_ERROR_CODE
NVRM: DevinitGetVoltageDescriptorTable: Unrecognized version (0x30)
NVRM: bp @ ../../../../resman/kernel/devinit/nv/devinit_volt.c:3257

** ModsDrvBreakPoint **

-------------------------- END ASSERT INFO DUMP --------------------------

** ModsDrvBreakPoint **

------------------------- BEGIN ASSERT INFO DUMP -------------------------
ROR_CODE_FECS_DEAD_RING
NVRM: Possible bad register read: addr: 0x9a0470, regvalue: 0xbadf3000, error code: NV_PPRIV_SYS_PRI_ERROR_CODE_FECS_DEAD_RING
NVRM: Possible bad register read: addr: 0x9a0470, regvalue: 0xbadf3000, error code: NV_PPRIV_SYS_PRI_ERROR_CODE_FECS_DEAD_RING
NVRM: Possible bad register read: addr: 0x9a0470, regvalue: 0xbadf3000, error code: NV_PPRIV_SYS_PRI_ERROR_CODE_FECS_DEAD_RING
NVRM: Possible bad register read: addr: 0x17e318, regvalue: 0xbadf3000, error code: NV_PPRIV_SYS_PRI_ERROR_CODE_FECS_DEAD_RING
NVRM: Possible bad register read: addr: 0x9a050c, regvalue: 0xbadf3000, error code: NV_PPRIV_SYS_PRI_ERROR_CODE_FECS_DEAD_RING
NVRM: Possible bad register read: addr: 0x9a050c, regvalue: 0xbadf3000, error code: NV_PPRIV_SYS_PRI_ERROR_CODE_FECS_DEAD_RING
NVRM: inforomBBXLoadObject_IMPL: BBX object get failed, status=0x57
NVRM: *** Chipset Setup Function Error!
NVRM: inforomGetPPOObject: InfoROM PPO object header load failed, status=0x57
NVRM: clkRead_Finish_Mux: utilsclk.osm3.mux[0]: NV_ERR_INVALID_STATE: Active input 0 is not attached in the schematic.
NVRM: clkRead_Finish_Mux: NV_PTRIM_SYS_UTILSCLK_OUT_SWITCH: addr=0x0013718c cache=valid data=0x00000002 prev=0x00000002
NVRM: clkReadDomain_CLK2: utilsclk: Error reading clock domain (23). NV_STATUS=0x00000040
NVRM: clkReadDomain_CLK2: output.freqKHz=0KHz path=0xffffffff spread=2 fracdiv=255 hot=0
NVRM: _DevinitGetVoltageDeviceTable_1X_PSV: Failed to map PWM frequency: 675000 to raw period!
NVRM: bp @ ../../../../resman/kernel/devinit/nv/devinit_volt.c:4089

** ModsDrvBreakPoint **
NVRM: Possible bad register read: addr: 0x214a8, regvalue: 0xbadf510c, error code: Unknown SYS_PRI_ERROR_CODE
NVRM: DevinitGetVoltageDescriptorTable: Unrecognized version (0x30)
NVRM: bp @ ../../../../resman/kernel/devinit/nv/devinit_volt.c:3257

** ModsDrvBreakPoint **
NVRM: _voltGetVoltageDescriptorTable: Error parsing the VDT from VBIOS: status = 0x00000056
NVRM: bp @ ../../../../resman/kernel/pmgr/nv/vdt.c:2932

** ModsDrvBreakPoint **

-------------------------- END ASSERT INFO DUMP --------------------------

** ModsDrvBreakPoint **

------------------------- BEGIN ASSERT INFO DUMP -------------------------
VRM: Possible bad register read: addr: 0x9a0470, regvalue: 0xbadf3000, error code: NV_PPRIV_SYS_PRI_ERROR_CODE_FECS_DEAD_RING
NVRM: Possible bad register read: addr: 0x9a0470, regvalue: 0xbadf3000, error code: NV_PPRIV_SYS_PRI_ERROR_CODE_FECS_DEAD_RING
NVRM: Possible bad register read: addr: 0x17e318, regvalue: 0xbadf3000, error code: NV_PPRIV_SYS_PRI_ERROR_CODE_FECS_DEAD_RING
NVRM: Possible bad register read: addr: 0x9a050c, regvalue: 0xbadf3000, error code: NV_PPRIV_SYS_PRI_ERROR_CODE_FECS_DEAD_RING
NVRM: Possible bad register read: addr: 0x9a050c, regvalue: 0xbadf3000, error code: NV_PPRIV_SYS_PRI_ERROR_CODE_FECS_DEAD_RING
NVRM: inforomBBXLoadObject_IMPL: BBX object get failed, status=0x57
NVRM: *** Chipset Setup Function Error!
NVRM: inforomGetPPOObject: InfoROM PPO object header load failed, status=0x57
NVRM: clkRead_Finish_Mux: utilsclk.osm3.mux[0]: NV_ERR_INVALID_STATE: Active input 0 is not attached in the schematic.
NVRM: clkRead_Finish_Mux: NV_PTRIM_SYS_UTILSCLK_OUT_SWITCH: addr=0x0013718c cache=valid data=0x00000002 prev=0x00000002
NVRM: clkReadDomain_CLK2: utilsclk: Error reading clock domain (23). NV_STATUS=0x00000040
NVRM: clkReadDomain_CLK2: output.freqKHz=0KHz path=0xffffffff spread=2 fracdiv=255 hot=0
NVRM: _DevinitGetVoltageDeviceTable_1X_PSV: Failed to map PWM frequency: 675000 to raw period!
NVRM: bp @ ../../../../resman/kernel/devinit/nv/devinit_volt.c:4089

** ModsDrvBreakPoint **
NVRM: Possible bad register read: addr: 0x214a8, regvalue: 0xbadf510c, error code: Unknown SYS_PRI_ERROR_CODE
NVRM: DevinitGetVoltageDescriptorTable: Unrecognized version (0x30)
NVRM: bp @ ../../../../resman/kernel/devinit/nv/devinit_volt.c:3257

** ModsDrvBreakPoint **
NVRM: _voltGetVoltageDescriptorTable: Error parsing the VDT from VBIOS: status = 0x00000056
NVRM: bp @ ../../../../resman/kernel/pmgr/nv/vdt.c:2932

** ModsDrvBreakPoint **
NVRM: voltVdtStateInit_IMPL: Error fetching the VDT: status = 0x00000056
NVRM: bp @ ../../../../resman/kernel/pmgr/nv/vdt.c:120

** ModsDrvBreakPoint **

-------------------------- END ASSERT INFO DUMP --------------------------

** ModsDrvBreakPoint **

------------------------- BEGIN ASSERT INFO DUMP -------------------------
000, error code: NV_PPRIV_SYS_PRI_ERROR_CODE_FECS_DEAD_RING
NVRM: Possible bad register read: addr: 0x17e318, regvalue: 0xbadf3000, error code: NV_PPRIV_SYS_PRI_ERROR_CODE_FECS_DEAD_RING
NVRM: Possible bad register read: addr: 0x9a050c, regvalue: 0xbadf3000, error code: NV_PPRIV_SYS_PRI_ERROR_CODE_FECS_DEAD_RING
NVRM: Possible bad register read: addr: 0x9a050c, regvalue: 0xbadf3000, error code: NV_PPRIV_SYS_PRI_ERROR_CODE_FECS_DEAD_RING
NVRM: inforomBBXLoadObject_IMPL: BBX object get failed, status=0x57
NVRM: *** Chipset Setup Function Error!
NVRM: inforomGetPPOObject: InfoROM PPO object header load failed, status=0x57
NVRM: clkRead_Finish_Mux: utilsclk.osm3.mux[0]: NV_ERR_INVALID_STATE: Active input 0 is not attached in the schematic.
NVRM: clkRead_Finish_Mux: NV_PTRIM_SYS_UTILSCLK_OUT_SWITCH: addr=0x0013718c cache=valid data=0x00000002 prev=0x00000002
NVRM: clkReadDomain_CLK2: utilsclk: Error reading clock domain (23). NV_STATUS=0x00000040
NVRM: clkReadDomain_CLK2: output.freqKHz=0KHz path=0xffffffff spread=2 fracdiv=255 hot=0
NVRM: _DevinitGetVoltageDeviceTable_1X_PSV: Failed to map PWM frequency: 675000 to raw period!
NVRM: bp @ ../../../../resman/kernel/devinit/nv/devinit_volt.c:4089

** ModsDrvBreakPoint **
NVRM: Possible bad register read: addr: 0x214a8, regvalue: 0xbadf510c, error code: Unknown SYS_PRI_ERROR_CODE
NVRM: DevinitGetVoltageDescriptorTable: Unrecognized version (0x30)
NVRM: bp @ ../../../../resman/kernel/devinit/nv/devinit_volt.c:3257

** ModsDrvBreakPoint **
NVRM: _voltGetVoltageDescriptorTable: Error parsing the VDT from VBIOS: status = 0x00000056
NVRM: bp @ ../../../../resman/kernel/pmgr/nv/vdt.c:2932

** ModsDrvBreakPoint **
NVRM: voltVdtStateInit_IMPL: Error fetching the VDT: status = 0x00000056
NVRM: bp @ ../../../../resman/kernel/pmgr/nv/vdt.c:120

** ModsDrvBreakPoint **
NVRM: voltVoltDeviceLegacyStateInit_IMPL: Failed to obtain Power Control Table from VBIOS. status = 0x0000ffff
NVRM: bp @ ../../../../resman/kernel/pmgr/nv/voltdev.c:198

** ModsDrvBreakPoint **

-------------------------- END ASSERT INFO DUMP --------------------------

** ModsDrvBreakPoint **

------------------------- BEGIN ASSERT INFO DUMP -------------------------
RING
NVRM: Possible bad register read: addr: 0x9a050c, regvalue: 0xbadf3000, error code: NV_PPRIV_SYS_PRI_ERROR_CODE_FECS_DEAD_RING
NVRM: Possible bad register read: addr: 0x9a050c, regvalue: 0xbadf3000, error code: NV_PPRIV_SYS_PRI_ERROR_CODE_FECS_DEAD_RING
NVRM: inforomBBXLoadObject_IMPL: BBX object get failed, status=0x57
NVRM: *** Chipset Setup Function Error!
NVRM: inforomGetPPOObject: InfoROM PPO object header load failed, status=0x57
NVRM: clkRead_Finish_Mux: utilsclk.osm3.mux[0]: NV_ERR_INVALID_STATE: Active input 0 is not attached in the schematic.
NVRM: clkRead_Finish_Mux: NV_PTRIM_SYS_UTILSCLK_OUT_SWITCH: addr=0x0013718c cache=valid data=0x00000002 prev=0x00000002
NVRM: clkReadDomain_CLK2: utilsclk: Error reading clock domain (23). NV_STATUS=0x00000040
NVRM: clkReadDomain_CLK2: output.freqKHz=0KHz path=0xffffffff spread=2 fracdiv=255 hot=0
NVRM: _DevinitGetVoltageDeviceTable_1X_PSV: Failed to map PWM frequency: 675000 to raw period!
NVRM: bp @ ../../../../resman/kernel/devinit/nv/devinit_volt.c:4089

** ModsDrvBreakPoint **
NVRM: Possible bad register read: addr: 0x214a8, regvalue: 0xbadf510c, error code: Unknown SYS_PRI_ERROR_CODE
NVRM: DevinitGetVoltageDescriptorTable: Unrecognized version (0x30)
NVRM: bp @ ../../../../resman/kernel/devinit/nv/devinit_volt.c:3257

** ModsDrvBreakPoint **
NVRM: _voltGetVoltageDescriptorTable: Error parsing the VDT from VBIOS: status = 0x00000056
NVRM: bp @ ../../../../resman/kernel/pmgr/nv/vdt.c:2932

** ModsDrvBreakPoint **
NVRM: voltVdtStateInit_IMPL: Error fetching the VDT: status = 0x00000056
NVRM: bp @ ../../../../resman/kernel/pmgr/nv/vdt.c:120

** ModsDrvBreakPoint **
NVRM: voltVoltDeviceLegacyStateInit_IMPL: Failed to obtain Power Control Table from VBIOS. status = 0x0000ffff
NVRM: bp @ ../../../../resman/kernel/pmgr/nv/voltdev.c:198

** ModsDrvBreakPoint **
NVRM: voltStateInitLocked_IMPL: Error initializing SW state for VOLTAGE_DEVICE. status = 0x0000ffff
NVRM: bp @ ../../../../resman/kernel/pmgr/nv/objvolt.c:192

** ModsDrvBreakPoint **

-------------------------- END ASSERT INFO DUMP --------------------------
Error 000000000229 : Gpu.Initialize hardware was not initialized
Error 000000000229 : Global.PrintGpuInitError hardware was not initialized
Error 000000000229 : Global.InitializeGpuTests hardware was not initialized

Error Code = 000000000818 (Mods detected an assertion failure)


####### #### ######## ###
####### ###### ######## ###
## ## ## ## ###
## ## ## ## ###
####### ######## ## ###
####### ######## ## ###
## ## ## ## ###
## ## ## ######## ########
## ## ## ######## ########


MODS end : Mon Feb 5 10:55:55 2024 [4.372 seconds (00:00:04.372 h:m:s)]

Серьезно ни у кого нет идей? снова у меня единственного такая неисправность?

Просто просьба не в тему- убирайте логи под спойлер. С телефона читать очень не удобно.

не знаю как это сделать, не могу найти

[spoil=][spoil] во вторых скобках поставьте слэш, чтобы вышло /spoil. Всё, что между скобками будет под спойлером

идей может быть много, но нет краткого пособия по дефекту "ошибки по всем чипам памяти".

с учетом того что изначально вы не придали значения сбитым и криво паянным элементам на плате, стоит проверить а не упустили ли вы еще чего?!

+ банально катнуть ГПУ и память уже бы успели, мало ли что под нее попасть могло + особенности прижимной пластины.