U-Boot 2010.06 (Jun 12 2018 - 19:20:21)

Check spi flash controller v350... Found
Spi(cs1) ID: 0xC2 0x20 0x18 0xC2 0x20 0x18
Spi(cs1): Block:64KB Chip:16MB Name:"MX25L128XX"
In: serial
Out: serial
Err: serial
Hit any key to stop autoboot: 0
16384 KiB hi_sfc at 0:0 is now current device

## Booting kernel from Legacy Image at 82000000 ...
Image Name: Linux-3.4.35
Image Type: ARM Linux Kernel Image (uncompressed)
Data Size: 2550712 Bytes = 2.4 MiB
Load Address: 80008000
Entry Point: 80008000
Loading Kernel Image ... OK
OK

Starting kernel ...

Uncompressing Linux... done, booting the kernel.
[ 0.000000] Booting Linux on physical CPU 0
[ 0.000000] Linux version 3.4.35 (qin@ubuntu) (gcc version 4.8.3 20131202 (prerelease) (Hisilicon_v300) ) #26 Fri May 25 14:54:26 CST 2018
[ 0.000000] CPU: ARMv7 Processor [410fc075] revision 5 (ARMv7), cr=10c53c7d
[ 0.000000] CPU: PIPT / VIPT nonaliasing data cache, VIPT aliasing instruction cache
[ 0.000000] Machine: hi3516a
[ 0.000000] Memory policy: ECC disabled, Data cache writeback
[ 0.000000] Built 1 zonelists in Zone order, mobility grouping on. Total pages: 18288
[ 0.000000] Kernel command line: mem=72M console=ttyAMA0,115200 root=/dev/mtdblock3 rootfstype=squashfs rw init=/init mtdparts=hi_sfc:256k(u-boot)ro,64k(env),3072k(kernel),3584k(rootfs),512k(config),-(app)
[ 0.000000] PID hash table entries: 512 (order: -1, 2048 bytes)
[ 0.000000] Dentry cache hash table entries: 16384 (order: 4, 65536 bytes)
[ 0.000000] Inode-cache hash table entries: 8192 (order: 3, 32768 bytes)
[ 0.000000] Memory: 72MB = 72MB total
[ 0.000000] Memory: 67968k/67968k available, 5760k reserved, 0K highmem
[ 0.000000] Virtual kernel memory layout:
[ 0.000000] vector : 0xffff0000 - 0xffff1000 ( 4 kB)
[ 0.000000] fixmap : 0xfff00000 - 0xfffe0000 ( 896 kB)
[ 0.000000] vmalloc : 0xc5000000 - 0xff000000 ( 928 MB)
[ 0.000000] lowmem : 0xc0000000 - 0xc4800000 ( 72 MB)
[ 0.000000] modules : 0xbf000000 - 0xc0000000 ( 16 MB)
[ 0.000000] .text : 0xc0008000 - 0xc0482000 (4584 kB)
[ 0.000000] .init : 0xc0482000 - 0xc04a371c ( 134 kB)
[ 0.000000] .data : 0xc04a4000 - 0xc04d4640 ( 194 kB)
[ 0.000000] .bss : 0xc04d4664 - 0xc04ebd08 ( 94 kB)
[ 0.000000] SLUB: Genslabs=11, HWalign=64, Order=0-3, MinObjects=0, CPUs=1, Nodes=1
[ 0.000000] NR_IRQS:128
[ 0.000000] sched_clock: 32 bits at 49MHz, resolution 20ns, wraps every 86767ms
[ 0.000000] Console: colour dummy device 80x30
[ 0.000105] Calibrating delay loop... 1699.02 BogoMIPS (lpj=8495104)
[ 0.060038] pid_max: default: 32768 minimum: 301
[ 0.060184] Mount-cache hash table entries: 512
[ 0.060626] Initializing cgroup subsys freezer
[ 0.060670] CPU: Testing write buffer coherency: ok
[ 0.060843] Setting up static identity map for 0x80372860 - 0x803728b8
[ 0.062694] dummy:
[ 0.062956] NET: Registered protocol family 16
[ 0.064913] Serial: AMBA PL011 UART driver
[ 0.064989] uart:0: ttyAMA0 at MMIO 0x20080000 (irq = 40) is a PL011 rev2
[ 0.286791] console [ttyAMA0] enabled
[ 0.290719] uart:1: ttyAMA1 at MMIO 0x20090000 (irq = 41) is a PL011 rev2
[ 0.297765] uart:2: ttyAMA2 at MMIO 0x200a0000 (irq = 42) is a PL011 rev2
[ 0.317877] bio: create slab <bio-0> at 0
[ 0.323240] SCSI subsystem initialized
[ 0.327554] hi-spi-master hi-spi-master.0: with 1 chip select slaves attached
[ 0.335171] hi-spi-master hi-spi-master.1: with 3 chip select slaves attached
[ 0.343082] usbcore: registered new interface driver usbfs
[ 0.348843] usbcore: registered new interface driver hub
[ 0.354371] usbcore: registered new device driver usb
[ 0.360937] Switching to clocksource timer0
[ 0.377328] NET: Registered protocol family 2
[ 0.381918] IP route cache hash table entries: 1024 (order: 0, 4096 bytes)
[ 0.389130] TCP established hash table entries: 4096 (order: 3, 32768 bytes)
[ 0.396285] TCP bind hash table entries: 4096 (order: 2, 16384 bytes)
[ 0.402771] TCP: Hash tables configured (established 4096 bind 4096)
[ 0.409120] TCP: reno registered
[ 0.412354] UDP hash table entries: 256 (order: 0, 4096 bytes)
[ 0.418194] UDP-Lite hash table entries: 256 (order: 0, 4096 bytes)
[ 0.424699] NET: Registered protocol family 1
[ 0.429269] RPC: Registered named UNIX socket transport module.
[ 0.435214] RPC: Registered udp transport module.
[ 0.439912] RPC: Registered tcp transport module.
[ 0.444616] RPC: Registered tcp NFSv4.1 backchannel transport module.
[ 0.464744] VFS: Disk quotas dquot_6.5.2
[ 0.469030] Dquot-cache hash table entries: 1024 (order 0, 4096 bytes)
[ 0.476620] squashfs: version 4.0 (2009/01/31) Phillip Lougher
[ 0.483331] NFS: Registering the id_resolver key type
[ 0.489295] jffs2: version 2.2. (NAND) © 2001-2006 Red Hat, Inc.
[ 0.496179] fuse init (API version 7.18)
[ 0.501288] msgmni has been set to 132
[ 0.506653] Block layer SCSI generic (bsg) driver version 0.4 loaded (major 254)
[ 0.514083] io scheduler noop registered
[ 0.518001] io scheduler deadline registered (default)
[ 0.523177] io scheduler cfq registered
[ 0.535449] brd: module loaded
[ 0.539927] Spi id table Version 1.22
[ 0.544068] Spi(cs1) ID: 0xC2 0x20 0x18 0xC2 0x20 0x18
[ 0.549222] SPI nor flash boot mode is 3 Bytes
[ 0.553693] Spi(cs1):
[ 0.555873] Block:64KB
[ 0.558227] Chip:16MB
[ 0.560588] Name:"MX25L128XX"
[ 0.563733] spi size: 16MB
[ 0.566432] chip num: 1
[ 0.568902] 6 cmdlinepart partitions found on MTD device hi_sfc
[ 0.574828] 6 cmdlinepart partitions found on MTD device hi_sfc
[ 0.580750] Creating 6 MTD partitions on "hi_sfc":
[ 0.585542] 0x000000000000-0x000000040000 : "u-boot"
[ 0.592319] 0x000000040000-0x000000050000 : "env"
[ 0.598708] 0x000000050000-0x000000350000 : "kernel"
[ 0.605413] 0x000000350000-0x0000006d0000 : "rootfs"
[ 0.612144] 0x0000006d0000-0x000000750000 : "config"
[ 0.618852] 0x000000750000-0x000001000000 : "app"
[ 0.625354] Found Nand Flash Controller V610.
[ 0.630216] Nand ID: 0x00 0x00 0x00 0x00 0x00 0x00 0x00 0x00
[ 0.635893] No NAND device found
[ 0.882120] Higmac dma_sg_phy: 0x84200000
[ 0.897151] higmac_mdio_bus: probed
[ 0.901894] ETH0: rmii, phy_addr=1, mii_name=mdio0
[ 0.906888] usbcore: registered new interface driver zd1201
[ 0.912694] ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver
[ 0.945132] hiusb-ehci hiusb-ehci.0: HIUSB EHCI
[ 0.949682] hiusb-ehci hiusb-ehci.0: new USB bus registered, assigned bus number 1
[ 0.957339] hiusb-ehci hiusb-ehci.0: irq 53, io mem 0x100b0000
[ 0.980046] hiusb-ehci hiusb-ehci.0: USB 0.0 started, EHCI 1.00
[ 0.986732] hub 1-0:1.0: USB hub found
[ 0.990517] hub 1-0:1.0: 1 port detected
[ 0.994969] ohci_hcd: USB 1.1 'Open' Host Controller (OHCI) Driver
[ 1.001414] hiusb-ohci hiusb-ohci.0: HIUSB OHCI
[ 1.005976] hiusb-ohci hiusb-ohci.0: new USB bus registered, assigned bus number 2
[ 1.013591] hiusb-ohci hiusb-ohci.0: irq 54, io mem 0x100a0000
[ 1.074828] hub 2-0:1.0: USB hub found
[ 1.078591] hub 2-0:1.0: 1 port detected
[ 1.083246] usbcore: registered new interface driver cdc_wdm
[ 1.088905] Initializing USB Mass Storage driver...
[ 1.094076] usbcore: registered new interface driver usb-storage
[ 1.100097] USB Mass Storage support registered.
[ 1.104709] i2c /dev entries driver
[ 1.109305] hisi_i2c hisi_i2c.0: Hisilicon [i2c-0] probed!
[ 1.115243] hisi_i2c hisi_i2c.1: Hisilicon [i2c-1] probed!
[ 1.121168] hisi_i2c hisi_i2c.2: Hisilicon [i2c-2] probed!
[ 1.129440] ######################### host->id:0
[ 1.136175] ######################### host->id:1
[ 1.141806] usbcore: registered new interface driver usbhid
[ 1.147378] usbhid: USB HID core driver
[ 1.151983] TCP: cubic registered
[ 1.155299] Initializing XFRM netlink socket
[ 1.160908] NET: Registered protocol family 10
[ 1.166080] NET: Registered protocol family 17
[ 1.170587] NET: Registered protocol family 15
[ 1.175069] lib80211: common routines for IEEE802.11 drivers
[ 1.180760] Registering the dns_resolver key type
[ 1.185577] VFP support v0.3: implementor 41 architecture 2 part 30 variant 7 rev 5
[ 1.196174] VFS: Mounted root (squashfs filesystem) readonly on device 31:3.
[ 1.203447] Freeing init memory: 132K
[ 1.208896] Failed to execute /init. Attempting defaults...

_ _ _ _ _ _ _ _ _ _ _ _
\ _ _ _ _ _ ___
/ /__/ \ |_/
/ __ / - _ ___
/ / / / / /
_ _ _ _/ / / \_/ \_ ______
___________\___\__________________

[RCS]: /etc/init.d/S00devs
[RCS]: /etc/init.d/S01udev
Not recognise ACTION:change
Not recognise ACTION:change
[RCS]: /etc/init.d/S80network
*** Board tools : ver0.0.1_20121120 ***
[debug]: {source/utils/cmdshell.c:166}cmdstr:himm
0x200f0174: 0x00000001 --> 0x00000002
[END]
[ 3.771139] ADDRCONF(NETDEV_UP): eth0: link is not ready
^vv^: tar -zxf /mnt/app/ipcam.tgz -C /home/bvtech
[ 5.920201] PHY: mdio0:01 - Link is Up - 100/Full
[ 5.924994] ADDRCONF(NETDEV_CHANGE): eth0: link becomes ready
-

U-Boot 2010.06 (Jun 12 2018 - 19:20:21)

Check spi flash controller v350... Found
Spi(cs1) ID: 0xC2 0x20 0x18 0xC2 0x20 0x18
Spi(cs1): Block:64KB Chip:16MB Name:"MX25L128XX"
In: serial
Out: serial
Err: serial
Hit any key to stop autoboot: 0
16384 KiB hi_sfc at 0:0 is now current device

## Booting kernel from Legacy Image at 82000000 ...
Image Name: Linux-3.4.35
Image Type: ARM Linux Kernel Image (uncompressed)
Data Size: 2550712 Bytes = 2.4 MiB
Load Address: 80008000
Entry Point: 80008000
Loading Kernel Image ... OK
OK

Starting kernel ...

Uncompressing Linux... done, booting the kernel.
[ 0.000000] Booting Linux on physical CPU 0
[ 0.00000-

U-Boot 2010.06 (Jun 12 2018 - 19:20:21)

Check spi flash controller v350... Found
Spi(cs1) ID: 0xC2 0x20 0x18 0xC2 0x20 0x18
Spi(cs1): Block:64KB Chip:16MB Name:"MX25L128XX"
In: serial
Out: serial
Err: serial
Hit any key to stop autoboot: 0
hi3516d # help
Unknown command 'р-help' - try 'help'
hi3516d # help
? - alias for 'help'
base - print or set address offset
bootm - boot application image from memory
bootp - boot image via network using BOOTP/TFTP protocol
cmp - memory compare
cp - memory copy
crc32 - checksum calculation
ddr - ddr training function
fatinfo - print information about filesystem
fatload - load binary file from a dos filesystem
fatls - list files in a directory (default /)
getinfo - print hardware information
go - start application at address 'addr'
help - print command description/usage
loadb - load binary file over serial line (kermit mode)
loady - load binary file over serial line (ymodem mode)
loop - infinite loop on address range
md - memory display
mii - MII utility commands
mm - memory modify (auto-incrementing address)
mtest - simple RAM read/write test
mw - memory write (fill)
nm - memory modify (constant address)
ping - send ICMP ECHO_REQUEST to network host
printenv- print environment variables
rarpboot- boot image via network using RARP/TFTP protocol
reset - Perform RESET of the CPU
saveenv - save environment variables to persistent storage
setenv - set environment variables
sf - SPI flash sub-system
tftp - tftp - download or upload image via network using TFTP protocol
usb - USB sub-system
usbboot - boot from USB device
version - print monitor version
hi3516d

U-Boot 2010.06 (Jun 12 2018 - 19:20:21)

Check spi flash controller v350... Found
Spi(cs1) ID: 0xC2 0x20 0x18 0xC2 0x20 0x18
Spi(cs1): Block:64KB Chip:16MB Name:"MX25L128XX"
In: serial
Out: serial
Err: serial
Hit any key to stop autoboot: 0
16384 KiB hi_sfc at 0:0 is now current device

## Booting kernel from Legacy Image at 82000000 ...
Image Name: Linux-3.4.35
Image Type: ARM Linux Kernel Image (uncompressed)
Data Size: 2550712 Bytes = 2.4 MiB
Load Address: 80008000
Entry Point: 80008000
Loading Kernel Image ... OK
OK

Starting kernel ...

Uncompressing Linux... done, booting the kernel.
[ 0.000000] Booting Linux on physical CPU 0
[ 0.000000] Linux version 3.4.35 (qin@ubuntu) (gcc version 4.8.3 20131202 (prerelease) (Hisilicon_v300) ) #26 Fri May 25 14:54:26 CST 2018
[ 0.000000] CPU: ARMv7 Processor [410fc075] revision 5 (ARMv7), cr=10c53c7d
[ 0.000000] CPU: PIPT / VIPT nonaliasing data cache, VIPT aliasing instruction cache
[ 0.000000] Machine: hi3516a
[ 0.000000] Memory policy: ECC disabled, Data cache writeback
[ 0.000000] Built 1 zonelists in Zone order, mobility grouping on. Total pages: 18288
[ 0.000000] Kernel command line: mem=72M console=ttyAMA0,115200 root=/dev/mtdblock3 rootfstype=squashfs rw init=/init mtdparts=hi_sfc:256k(u-boot)ro,64k(env),3072k(kernel),3584k(rootfs),512k(config),-(app)
[ 0.000000] PID hash table entries: 512 (order: -1, 2048 bytes)
[ 0.000000] Dentry cache hash table entries: 16384 (order: 4, 65536 bytes)
[ 0.000000] Inode-cache hash table entries: 8192 (order: 3, 32768 bytes)
[ 0.000000] Memory: 72MB = 72MB total
[ 0.000000] Memory: 67968k/67968k available, 5760k reserved, 0K highmem
[ 0.000000] Virtual kernel memory layout:
[ 0.000000] vector : 0xffff0000 - 0xffff1000 ( 4 kB)
[ 0.000000] fixmap : 0xfff00000 - 0xfffe0000 ( 896 kB)
[ 0.000000] vmalloc : 0xc5000000 - 0xff000000 ( 928 MB)
[ 0.000000] lowmem : 0xc0000000 - 0xc4800000 ( 72 MB)
[ 0.000000] modules : 0xbf000000 - 0xc0000000 ( 16 MB)
[ 0.000000] .text : 0xc0008000 - 0xc0482000 (4584 kB)
[ 0.000000] .init : 0xc0482000 - 0xc04a371c ( 134 kB)
[ 0.000000] .data : 0xc04a4000 - 0xc04d4640 ( 194 kB)
[ 0.000000] .bss : 0xc04d4664 - 0xc04ebd08 ( 94 kB)
[ 0.000000] SLUB: Genslabs=11, HWalign=64, Order=0-3, MinObjects=0, CPUs=1, Nodes=1
[ 0.000000] NR_IRQS:128
[ 0.000000] sched_clock: 32 bits at 49MHz, resolution 20ns, wraps every 86767ms
[ 0.000000] Console: colour dummy device 80x30
[ 0.000106] Calibrating delay loop... 1699.02 BogoMIPS (lpj=8495104)
[ 0.060037] pid_max: default: 32768 minimum: 301
[ 0.060184] Mount-cache hash table entries: 512
[ 0.060623] Initializing cgroup subsys freezer
[ 0.060667] CPU: Testing write buffer coherency: ok
[ 0.060844] Setting up static identity map for 0x80372860 - 0x803728b8
[ 0.062687] dummy:
[ 0.062947] NET: Registered protocol family 16
[ 0.064912] Serial: AMBA PL011 UART driver
[ 0.064986] uart:0: ttyAMA0 at MMIO 0x20080000 (irq = 40) is a PL011 rev2
[ 0.286787] console [ttyAMA0] enabled
[ 0.290717] uart:1: ttyAMA1 at MMIO 0x20090000 (irq = 41) is a PL011 rev2
[ 0.297761] uart:2: ttyAMA2 at MMIO 0x200a0000 (irq = 42) is a PL011 rev2
[ 0.317842] bio: create slab <bio-0> at 0
[ 0.323182] SCSI subsystem initialized
[ 0.327499] hi-spi-master hi-spi-master.0: with 1 chip select slaves attached
[ 0.335112] hi-spi-master hi-spi-master.1: with 3 chip select slaves attached
[ 0.343024] usbcore: registered new interface driver usbfs
[ 0.348786] usbcore: registered new interface driver hub
[ 0.354316] usbcore: registered new device driver usb
[ 0.360876] Switching to clocksource timer0
[ 0.377235] NET: Registered protocol family 2
[ 0.381814] IP route cache hash table entries: 1024 (order: 0, 4096 bytes)
[ 0.389032] TCP established hash table entries: 4096 (order: 3, 32768 bytes)
[ 0.396183] TCP bind hash table entries: 4096 (order: 2, 16384 bytes)
[ 0.402669] TCP: Hash tables configured (established 4096 bind 4096)
[ 0.409018] TCP: reno registered
[ 0.412251] UDP hash table entries: 256 (order: 0, 4096 bytes)
[ 0.418091] UDP-Lite hash table entries: 256 (order: 0, 4096 bytes)
[ 0.424597] NET: Registered protocol family 1
[ 0.429174] RPC: Registered named UNIX socket transport module.
[ 0.435122] RPC: Registered udp transport module.
[ 0.439820] RPC: Registered tcp transport module.
[ 0.444523] RPC: Registered tcp NFSv4.1 backchannel transport module.
[ 0.464673] VFS: Disk quotas dquot_6.5.2
[ 0.468955] Dquot-cache hash table entries: 1024 (order 0, 4096 bytes)
[ 0.476524] squashfs: version 4.0 (2009/01/31) Phillip Lougher
[ 0.483232] NFS: Registering the id_resolver key type
[ 0.489192] jffs2: version 2.2. (NAND) © 2001-2006 Red Hat, Inc.
[ 0.496071] fuse init (API version 7.18)
[ 0.501180] msgmni has been set to 132
[ 0.506552] Block layer SCSI generic (bsg) driver version 0.4 loaded (major 254)
[ 0.513981] io scheduler noop registered
[ 0.517899] io scheduler deadline registered (default)
[ 0.523076] io scheduler cfq registered
[ 0.535333] brd: module loaded
[ 0.539786] Spi id table Version 1.22
[ 0.543914] Spi(cs1) ID: 0xC2 0x20 0x18 0xC2 0x20 0x18
[ 0.549069] SPI nor flash boot mode is 3 Bytes
[ 0.553536] Spi(cs1):
[ 0.555716] Block:64KB
[ 0.558069] Chip:16MB
[ 0.560429] Name:"MX25L128XX"
[ 0.563574] spi size: 16MB
[ 0.566272] chip num: 1
[ 0.568742] 6 cmdlinepart partitions found on MTD device hi_sfc
[ 0.574667] 6 cmdlinepart partitions found on MTD device hi_sfc
[ 0.580590] Creating 6 MTD partitions on "hi_sfc":
[ 0.585382] 0x000000000000-0x000000040000 : "u-boot"
[ 0.592156] 0x000000040000-0x000000050000 : "env"
[ 0.598551] 0x000000050000-0x000000350000 : "kernel"
[ 0.605277] 0x000000350000-0x0000006d0000 : "rootfs"
[ 0.612001] 0x0000006d0000-0x000000750000 : "config"
[ 0.618712] 0x000000750000-0x000001000000 : "app"
[ 0.625215] Found Nand Flash Controller V610.
[ 0.630061] Nand ID: 0x00 0x00 0x00 0x00 0x00 0x00 0x00 0x00
[ 0.635738] No NAND device found
[ 0.881996] Higmac dma_sg_phy: 0x84200000
[ 0.897071] higmac_mdio_bus: probed
[ 0.901813] ETH0: rmii, phy_addr=1, mii_name=mdio0
[ 0.906809] usbcore: registered new interface driver zd1201
[ 0.912624] ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver
[ 0.945061] hiusb-ehci hiusb-ehci.0: HIUSB EHCI
[ 0.949616] hiusb-ehci hiusb-ehci.0: new USB bus registered, assigned bus number 1
[ 0.957274] hiusb-ehci hiusb-ehci.0: irq 53, io mem 0x100b0000
[ 0.980047] hiusb-ehci hiusb-ehci.0: USB 0.0 started, EHCI 1.00
[ 0.986723] hub 1-0:1.0: USB hub found
[ 0.990509] hub 1-0:1.0: 1 port detected
[ 0.994958] ohci_hcd: USB 1.1 'Open' Host Controller (OHCI) Driver
[ 1.001404] hiusb-ohci hiusb-ohci.0: HIUSB OHCI
[ 1.005964] hiusb-ohci hiusb-ohci.0: new USB bus registered, assigned bus number 2
[ 1.013580] hiusb-ohci hiusb-ohci.0: irq 54, io mem 0x100a0000
[ 1.074825] hub 2-0:1.0: USB hub found
[ 1.078589] hub 2-0:1.0: 1 port detected
[ 1.083240] usbcore: registered new interface driver cdc_wdm
[ 1.088899] Initializing USB Mass Storage driver...
[ 1.094073] usbcore: registered new interface driver usb-storage
[ 1.100094] USB Mass Storage support registered.
[ 1.104706] i2c /dev entries driver
[ 1.109310] hisi_i2c hisi_i2c.0: Hisilicon [i2c-0] probed!
[ 1.115246] hisi_i2c hisi_i2c.1: Hisilicon [i2c-1] probed!
[ 1.121162] hisi_i2c hisi_i2c.2: Hisilicon [i2c-2] probed!
[ 1.129442] ######################### host->id:0
[ 1.136180] ######################### host->id:1
[ 1.141814] usbcore: registered new interface driver usbhid
[ 1.147385] usbhid: USB HID core driver
[ 1.151983] TCP: cubic registered
[ 1.155298] Initializing XFRM netlink socket
[ 1.160894] NET: Registered protocol family 10
[ 1.166068] NET: Registered protocol family 17
[ 1.170578] NET: Registered protocol family 15
[ 1.175059] lib80211: common routines for IEEE802.11 drivers
[ 1.180754] Registering the dns_resolver key type
[ 1.185570] VFP support v0.3: implementor 41 architecture 2 part 30 variant 7 rev 5
[ 1.196158] VFS: Mounted root (squashfs filesystem) readonly on device 31:3.
[ 1.203431] Freeing init memory: 132K
[ 1.208877] Failed to execute /init. Attempting defaults...

_ _ _ _ _ _ _ _ _ _ _ _
\ _ _ _ _ _ ___
/ /__/ \ |_/
/ __ / - _ ___
/ / / / / /
_ _ _ _/ / / \_/ \_ ______
___________\___\__________________

[RCS]: /etc/init.d/S00devs
[RCS]: /etc/init.d/S01udev
Not recognise ACTION:change
Not recognise ACTION:change
[RCS]: /etc/init.d/S80network
*** Board tools : ver0.0.1_20121120 ***
[debug]: {source/utils/cmdshell.c:166}cmdstr:himm
0x200f0174: 0x00000001 --> 0x00000002
[END]
[ 3.769500] ADDRCONF(NETDEV_UP): eth0: link is not ready
^vv^: tar -zxf /mnt/app/ipcam.tgz -C /home/bvtech
[ 5.920201] PHY: mdio0:01 - Link is Up - 100/Full
[ 5.924990] ADDRCONF(NETDEV_CHANGE): eth0: link becomes ready
tar: invalid tar magic
ERR: decompress application failed! start recovery.
System startup success.
(none) login:

hi3516d # printenv
bootcmd=sf probe 0;sf read 0x82000000 0x50000 0x300000;bootm 0x82000000
bootdelay=1
baudrate=115200
ethaddr=D0:22:12:88:88:88
gatewayip=192.168.1.1
netmask=255.255.255.0
chiptype=hi3516d
bootargs=mem=72M console=ttyAMA0,115200 root=/dev/mtdblock3 rootfstype=squashfs rw init=/init mtdparts=hi_sfc:256k(u-boot)ro,64k(env),3072k(kernel),3584k(rootfs),512k(config),-(app)
ipaddr=192.168.0.142
serverip=192.168.0.178
uuid=037db405-2391-40c5-b42b-fcb17209980e
BoardType=600108020-BV-H0820
lenstype=YT_MOTOR_27_135
mac=f0:23:b9:48:fd:b3
serialno=PNLIP5Z5MPALM17Z0197030104
qrcode=R1XH3GF3AE13FP8K111A
license=a4bba9cb8d49798f1b763019872ed0d4
sensortype=imx335
stdin=serial
stdout=serial
stderr=serial
verify=n
ver=U-Boot 2010.06 (Jun 12 2018 - 19:20:21)

Environment size: 748/65532 bytes

hi3516d # tftp
ETH0: PHY(phyaddr=1, rgmii) not link!
higmac init fail!